User manual KLIPSCH GMX D-5.1

[. . . ] To reduce the risk of electric shock and fire, do not remove the cover or back plate of the device enclosure. The international symbol of a lightning bolt inside a triangle is intended to alert the user to uninsulated "dangerous voltage" within the device enclosure. The international symbol of an exclamation point inside a triangle is intended to alert the user to the presence of important operating, maintenance and servicing information in the manual accompanying the device. To reduce the risk of fire or electrical shock, do not expose this equipment to rain or moisture. [. . . ] Failure to observe this caution may result in loud hums, buzzes, or pops that will at the very least be annoying and that in the extreme may damage your speakers. Unpacking Carefully remove the system components from the carton: · 1 Subwoofer · 5 Satellite speakers on pedestal bases · 1 Digital preamplifier and control module · 1 Multipin control cable with DC supply cord · 5 Speaker cables with RCA connector on one end · 1 Stereo miniplug-to-RCA-sockets adaptor · 1 AC power cord 1. Tighten FIGURE 3 FIGURE 1 FIGURE 2 Power Connections The last setup steps are the power connections (see Fig. Plug the DC supply cord into the jack labeled "Decoder Supply" on the subwoofer cabinet. Next, plug the other end into the jack labeled "DC 7V IN" on the back of the GMX control module. Plug the subwoofer's power cord into a wall outlet or AC power strip. Your GMX D-5. 1 is now ready to rumble. The Control Module Everything you need to run the GMX D-5. 1 is on the face of the control module. These buttons are also used to adjust the levels of the speakers in the system relative to one another (channel balance). Choosing an input will cause its indicator LED above the button to light up. Modes that can be used will depend on the input and type of signal. · Dolby Digital Signals: If you have selected one of the digital inputs, it will automatically switch to the appropriate Dolby Digital mode when a Dolby Digital signal is present. The Dolby Digital indicator LED (above the Surround button) will light. Dolby Digital modes are available only when a Dolby Digital signal is present at the selected digital input; no surround changes may be made to a discrete Dolby Digital 5. 1 signal. The Surround button will be active in Dolby Digital mode only when the signal is two-channel stereo, as described immediately below. · Stereo Signals: If you have selected the analog input or a digital input receiving a PCM signal, such as from a CD, you have a choice of four modes: Stereo, 5-Channel Stereo, Dolby Pro Logic II Cinema and Music. The Dolby Pro Logic II modes can also be applied to a Stereo Dolby Digital signal. Switch modes by pressing the Surround button until you reach the one you want, as indicated by the LEDs above the button. When on, the LED above the button will light and you will hear noise for several seconds from each satellite speaker in turn. The signal will rotate from speaker to speaker in this fashion until you turn it off. This signal has two uses: · Making sure that all speakers are connected and working. Because the five satellites in the GMX D-5. 1 are identical, you will usually get correct channel balance automatically. Use the volume pads to raise or lower the surround level until you get the balance that you want. The central display will show "SR" or "SL" to indicate adjustment of the Surround Right or Surround Left output channel, and then switch to indicate how much boost or cut you have applied in decibels (dB). Pressing the button once will allow you to adjust the surround right channel. [. . . ] This warranty does not cover damage due to misuse, abuse, negligence, acts of God, accident, commercial use or modification of, or to any part of this product. This warranty does not cover damage due to improper operation, maintenance or installation, or attempted repair by anyone other than KLIPSCH or someone authorized by KLIPSCH to do warranty work. This warranty is invalid if the factory applied serial number or date stamp has been altered or removed from this product. This Warranty is only valid for the origi nal purchaser and will automatically ter minate prior to expiration if this product is sold or otherwise trans ferred to another party . [. . . ]