User manual KLIPSCH IC-400-T

[. . . ] Position tilebridge over cutout hole, and insure that the tile rails rest on the t-grid struts. Thank you for purc hasing your Klipsc h IC-400-T, IC-525-T or IC-650-T in-ceiling speakers. The IC-400-T, IC-525-T and IC-650-T in-ceiling speakers have been designed for music reinforcement applications. Unobtrusive, these loudspeakers are engineered for easy, versatile installation. The IC-400-T, IC-525-T and IC-650-T feature an internal transformer for 70V/100V distributed-line systems. [. . . ] Replace the terminal cover and tighten the conduit/wire adapter to secure the wire. Caution: Be sure to comply with any and all building codes in your area. Caution: When connecting 70V or 100V distributed line systems, take care to ensure proper terminal connection. Connection to the low impedance terminal could result in speaker damage, amplifier damage, or both. 2. To install your IC-400-T, IC-525-T or IC-650-T cut out a hole in the ceiling using either the cardboard cutout template provided with your speakers or consult the measurements below. Pull wiring through hole. I C - 4 0 0 - T, I C - 5 2 5 - T 9. 125 " Ro u n d 10. 125 " Ro u n d IC-650-T 5. With a #2 Phillips screwdriver, tighten the four dog clamps until they are seated securely against the ceiling surface. Do not overtighten. Seismic Tab A seismic tab, located on the back of the speaker, is used as a secondary security point. To utilize the seismic tab, run a support wire from a secure point in the ceiling and attach it to the tab. Klipsch recommends the use of this tab in all installations as a secondary means of support. 1. 875W 3. 75W 7. 5W 15W 15W 7. 5W 3. 75W IC-400-T tap selectable 100V 70V 3. 75W 7. 5W 15W 30W 30W 15W 7. 5W IC-525-T tap selectable 100V 70V 7. 5W 15W 30W 60W 6. For installations using 70v/100v input connection, set the switch on the front panel to the desired setting. For applications where 8 Ohm impedance is desired, the switch should be set to 8 Ohms. Note: The speaker comes from the factory set at the lowest output setting (highest impedance). Using the flat of your hand, insert grille into speaker frame making sure it is securely seated and flush. 60W 30W 15W IC-650-T tap selectable 100V 70V IN - CEILING SPEAKERS I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T S P E C I F I C AT I O N S IC-400-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 70-20k Hz +/- 4 dB 50 watts (14. 5V) 100 dB 86dB 80 degrees 8 dB 6. 3 8 ohms, min 4. 2 ohms when switch is set to 8 ohm position 9" 9. 125" 8. 313" 8" 6. 25 lbs. 8 W Black and White 5 " WO O F E R A N D 1 " T I TA N I U M D I A P H R AG M C O M P R E S S I O N D R I V E R O N A 2 " RO U N D T R AC T R I X H O R N Ve n t e d V i a A 1 " Tr a c t r i x p o r t IC-525-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 65-20k Hz +/- 4 dB 65 watts (16. 5V) 104 dB 89dB 10 5 d e g r e e s 6. 5 dB 4. 5 8 ohms, min 4. 2 ohms; switch set in 8 ohm position 9" 9. 125" 9. 188" 8. 875" 8. 25 lbs. 7 5 " WO O F E R A N D 1 " T I TA N I U M D I A P H R AG M C O M P R E S S I O N D R I V E R O N A 3 . 5 " RO U N D X T M O D I F I E D T R AC T R I X H O R N Ve n t e d V i a A 1 " Tr a c t r i x p o r t IC-650-T FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 50-20k Hz +/- 4 dB 80 watts (18. 8 V) 106 dB 90dB 10 5 d e g r e e s 6. 5 dB 4. 5 8 ohms, min 4. 4 ohms; switch set in 8 ohm position 10" 10. 125" 10. 938" 10. 625" 11. [. . . ] REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE. Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. [. . . ]