User manual KLIPSCH ICON SERIES

[. . . ] The mains plug of the power supply cord shall remain readily operable. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. WARNING: No naked flame sources ­ such as candles ­ should be placed on the product. WARNING RISK OF ELECTRIC SHOCK. [. . . ] · Position them equal distance from the back wall (if they are not wall-mounted. ) · Position them at the same height above the floor (for non-floor standing models) with the high frequency drivers at seated ear height. · Angle speakers toward the listener and even with or forward of any adjacent obstructions (if they are not wall-mounted. ) e · Placing them near a corner or wall provides the greatest amount of bass while moving the speakers away from room boundaries reduces bass energy. · Asymmetrical placement of a pair of speakers from adjacent side walls can smooth room-induced bass unevenness. · Bookshelf models may be placed on shelves or optional floor stands. · Experiment with the above guidelines to suit your taste and to compensate for your room's acoustic characteristics. Active Floorstander Connections (See figure 5. )(XF-48 only) · In addition to the standard connections, the speakers have an RCA-jack line-level input that can be used as an input from your A/V receiver or electronics. Do not connect both the standard SPEAKER IN and the LINE IN inputs at the same time as damage to your equipment could result. · Your floorstanding speakers have a built-in amplifier that needs to be connected to an AC outlet. Once plugged in, it will be either ON or in STANDBY depending upon the position of the AUTO POWER switch. You must unplug the power cord from the AC outlet to completely turn off your speaker during extended periods. vacations. ) Center Channel Speakers (See Figures 2A, 2B and 3. ) · Place immediately above or below the center of your video display. · These models are supplied with a tilt rod to compensate for placements above or below seated ear height. · Use the supplied rubber pad to protect the front bottom edge of the speaker. (See Figure 3. ) Active Floorstander Controls (See figure 5. )(XF-48 only) Power - This switch allows you to select either "AUTO" or "ON" for the speakers built in amplifier. When "AUTO" is selected, the speaker will automatically turn on when it senses a signal. It will automatically turn off after 20 minutes if no signal is present. In the "ON" setting the speaker will remain on as long as the AC power cord is plugged into a wall socket. The power indicator LED on the front panel will illuminate BLUE when speaker is on and RED when the speaker is in standby. The LED will be off if the AC power cord is not connected to an AC outlet. Input Sensitivity - This switch adjusts the level of the input signal to optimize the performance of the built-in amplifier. Select "LOW" when connecting most A/V receivers via the "SPEAKER" or "LINE" inputs. Select "HIGH" when connecting devices such as the audio outputs of a TV to the "LINE" inputs. Surround Channel Speakers (See Figures 2A, 2B and 3. ) · Place above seated ear height (approximately 4-5 feet above the floor) on side or rear walls or on optional floorstands. · Attach wall bracket with an appropriately sized screw head screwed into a wall stud or wall anchor with a suitable weight bearing capacity. [. . . ] · Consult the dealer or an experienced radio/TV technician for help. Approved under the verification provision of FCC Part 15 as a Class B Digital Device. Caution: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this device. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada EU Compliance Information Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive 73/23/EEC and 2006/95/EC; Conforms to European Union EMC Directives 89/336/EEC and 2004/108/EC. WEEE Notice Note: This mark applies only to countries within the European Union (EU) and Norway. [. . . ]