User manual KLIPSCH ICON SUBWOOFERS

[. . . ] If it still won't fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. [. . . ] "Phase" - This screen is used to adjust the subwoofer's acoustic phase to match that of your main speakers. Use the Left/Right cursor keys to adjust the subwoofer's phase from 0° to 180°. The proper setting of this control is highly dependant on room acoustics and the position of your subwoofer in the room. After setting the volume and lowpass controls set the phase to 0 and listen to a recording with a prominent, repeating bass line in your intended listening position. Repeat this process with the 180° setting and use the setting that yields the greatest amount of bass output. If neither of these settings is better than the other experiment with intermediate settings. From this screen press the down or up cursor key to access other control settings. "Save Settings:" - This screen is used to store all of the above control settings in one of three memory presets ("Music", "Movie" and "Night"). Use the Left/Right cursor keys to select the desired preset and press the Enter key to store your current control settings. After the settings are stored in memory the display will return to the default "Volume" adjustment screen. From this screen press the up or down cursor key to access other control settings. "Disp Brightness" - This screen is used to adjust the brightness level of the display screen. Use the Left/Right cursor keys to select from any one of 4 different brightness intensities. From this screen press the down or up cursor key to access other control settings. Connections and Controls Caution!"LINE IN" -Accept signals from the Left and Right channel pre-amp, subwoofer or LFE outputs of your electronics. Connect to the "RIGHT" and/or "LEFT/LFE" inputs on the subwoofer's rear panel (Refer to figure 3). Controls All of the subwoofer's controls, and changes to control settings, are accessed through the cursor key pad and display on the top of the subwoofer's cabinet. The only exception to this is the main AC power switch which is located on the rear panel of the subwoofer. · Use the p (UP) or q (Down) key to scroll through the list of control options. · Use the t (Left) or u (Right) Key to make adjustments to a given control setting. · Use the Enter Key when the " 8 " appears on the display to store and recall custom settings or to lock the keypad. · After adjusting the individual control parameters for "Volume", "EQ Mode", "Low-pass filter" and "Phase", your settings can be stored in one of three user memories ("Movie", "Music" and "Night"). This allows for global recall of all of the above settings to tailor the subwoofer's performance to compensate for differing source material and uses. [. . . ] In some cases, modification to the mounting surface may be required where a new model is substituted. To obtain a repair or replacement under the terms of this warranty, please contact our customer Warranty Outside the U. S. and Canada The Warranty on this product if it is sold to a consumer outside of the United States and Canada shall comply with applicable law. To obtain any applicable warranty service, please contact the dealer from which you purchased this product, or the distributor that supplied this product. 5 Figure 1 - On-Wall Front Speaker Placement Figure 2 - Traditional Front Speaker Placement 6 Figure 3 - Line Level Connections XW-500d IR SENSOR LINE IN R L CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! ON ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE AND RATING. TO AVOID THE RISK OF FIRE UTILISER UN FUSIBLE OR ELECTRIC SHOCK, DO DE RECHANGE DE MEME NOT EXPOSE THIS EQUIPMENT R TYPE ET CALIBRE. [. . . ]