User manual KLIPSCH KSP300

[. . . ] Lightning and Periods of Non-Use ­ For added protection for this prodremove the cover or back plate of the device enclosure. There are uct during a lightning storm, or when it is left unattended and unused for no user serviceable parts inside. Refer servicing to an Aragon long periods of time, unplug it from the wall outlet and disconnect the authorized service center. This will prevent damage to the product due to lightning and powerline surges. [. . . ] Press the remote OK button or front-panel Stage Manager to enter the Speaker Configuration menu. Front Speakers Use the Left and Right buttons on the remote control or Stage Manager knob to configure the front left and right front speakers as Large or Small. Select Small (THX) when the front left and right speakers have limited bass response or if you simply want the bass from all channels to go to a subwoofer. Select Large for full low-frequency output to the front left and right speakers. The default THX setting for the front left and right loudspeakers is Small, which reroutes bass below the crossover frequency to the subwoofer output. (The crossover frequency can be adjusted in a subsequent menu. ) Once you have selected the correct speaker designation, press the Up button or the Stage Manager to move to Center Speaker configuration. If you select None in surround speaker configuration, the Stage One will automatically set the surround back speaker configuration to None. If you have both surround and surround back speakers, your only choice for this setting will be to choose the quantity­None, One or Two­as the size configuration will be set the same as that of the surround speakers. If your surround speakers are set to Large, you should make sure your surround back speakers can handle a full-range signal as well. If they cannot, you should set the surround speakers size to Small so that the bass for all of these speakers is redirected to the subwoofer. Use the Left and Right buttons on the remote or the Stage Manager knob to select the correct surround back speaker setting. Then press the up button on the remote or the Stage Manager knob to move to Subwoofer configuration. Subwoofer Center Speaker 18 The center speaker can be configured as Large, Small (THX), or None. If you select Small, the Stage One will reroute bass below the crossover frequency from the center channel to the subwoofer output if there is a subwoofer in the system; if there is no subwoofer and the front left and right speakers are There are three options for the subwoofer setting--No, Yes, and Ultra2. Press the Up button on the remote or the front-panel Stage Manager to proceed to surround right channel level setting. 19 KSP300 THX SURROUND PREAMPLIFIER SPEAKER DISTANCES Surround Back Right In the Speaker Distances menu, you will enter the distance from each speaker to the listening position. This enables the Stage One's DSP engine to set internal delays for time alignment of the speakers in the system to within 1/12th of a millisecond. Only speakers listed as present in the Speaker Configuration menu will appear in this menu. Press the OK on the remote button or the front-panel Stage Manager knob to enter the Speaker Distances menu. Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the surround back right speaker (if present) to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the surround back left speaker (if present). Surround Back Left Front Left Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the surround back left speaker (if present) to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the surround left speaker (if present). Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the front left speaker to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the center speaker (if present). Surround Left Center Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the left surround speaker to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the Subwoofer (if present). Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the center speaker (if present) to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the front right speaker. Subwoofer Front Right Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the subwoofer (if present) to the listening position. Press the OK button on the remote or the Stage Manager knob to exit the Speaker Distances menu and proceed to the THX Setup menu. Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the front right speaker to the listening position. Press the Up button on the remote or the Stage Manager knob to advance to distance setting for the right surround speaker (if present). Surround Right Use the Left and Right buttons on the remote or turn the front-panel Stage Manager knob to set the distance measured from the right surround speaker (if present) to the listening position. [. . . ] If you press the Right button on the remote control to change this setting to Yes and then press the OK button and the Stage One will revert to its factory default settings. Reprogram System The default setting is No. If an update is available for the Stage One, it can be downloaded into the processor from a computer through the RS-232 port. See the readme file included with the update for instructions on reprogramming the system. If there is any question about the operation, you should have your dealer perform it. [. . . ]