User manual KUSSMAUL 091-84
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KUSSMAUL 091-84. We hope that this KUSSMAUL 091-84 user guide will be useful to you.
Manual abstract: user guide KUSSMAUL 091-84
Detailed instructions for use are in the User's Guide.
[. . . ] This prevents contamination of the mechanism by road dirt and ensures long reliable life even when mounted in the most severe environment. circuit after the mating connector is inserted and before the connector is ejected. [. . . ] This eliminates arcing at the connector contacts and assures long contact life. As with all Auto Ejects, the Super 30 Auto Eject is connected to the starter circuit so that ejection occurs when the engine is cranked.
INSTALLATION INSTRUCTIONS
Step #1 wiring unit 1. Remove rear plastic cover from Super 30 Auto Eject by unscrewing (4) #8-32 screws. Snake wires though small cover strain relief and install wires as shown use 18 AWG wire minimum. Snake wires though large cover strain relief and install wires as shown use 10 AWG wire minimum. Test the unit to see if it is operational before mounting.
3.
4. When replacing with another connector, test carefully that the new connector will eject properly.
TORQUE SCREWS TO 16 LB-IN
10 AWG MINIMUM
GROUND
NEUTRAL TO AC LOAD ON VEHICLE
LINE
BACK OF SUPER 30 AUTO EJECT WITH REAR PLASTIC COVER REMOVED
3 CONDUCTOR 10 AWG MINIMUM
STRIP WIRES 5" FROM OUTER JACKET
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGULAR
WEST SAYVILLE, NY
. XX . XXX
DRAWN
DO NOT SCALE DRAWING
+ + -
. 005 . 001
FIGURE 2 AC WIRING
SIZE DW G NO.
T. Nugent
091-159
REV
FINSH
MAT:
SCALE
DATE
SHEET
OF
CONNECTOR ON PC BOARD NOTE: FUSE 3 AMP FUSE FOR 12 VOLT 2 AMP FUSE FOR 24 VOLT
PC BOARD + 12 VOLTS CONTINUOUS GROUND TO STARTER FUSE
3 CONDUCTOR 18 AWG WIRE
TOP OF SUPER 30 AUTO EJECT WITH REAR PLASTIC COVER REMOVED
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGULAR
WEST SAYVILLE, NY
. XX . XXX
DRAWN
DO NOT SCALE DRAWING
+ + -
. 005 . 001
FIGURE 3 DC WIRING
SIZE DW G NO. Nugent
FINSH
091-159
SCALE DATE SHEET OF
MAT:
4. 190
1. 010
6. 210
0. 330
4. 676
1. 475 0. 250
4. 735
1. 282
6. 123
8. 874
0. 500 5. 356 . 42
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES DECIMALS ANGULAR
WEST SAYVILLE, NY
. XX . XXX
DRAWN
DO NOT SCALE DRAWING
+ + -
. 005 . 001
OUTLINE DRAWING
SIZE DWG NO. Nugent
FINSH
091-159
SCALE DATE SHEET OF
MAT:
1 YEAR WARRANTY All Super 30 Auto Ejects manufactured by Kussmaul Electronics Company Inc. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 1 year from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. [. . . ] Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. This warranty does not include normal wear and tear, pitting of the electrical contacts, malfunction due to contamination of the mechanism, or any cracking, breakage or damage to the connector. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KUSSMAUL 091-84
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KUSSMAUL 091-84 will begin.