User manual LA CROSSE TECHNOLOGY WS-8610U

[. . . ] WS-8610 WIRELESS DATA LOGGING WEATHER STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this revolutionary 433MHz data logging weather station, which provides advanced datalogging and data-analysis functions for up to three outdoor temperature and humidity readings. The weather station is connectable to PC by the COM port and data importing to your PC is allowed. By utilizing the advanced software provided you might perform data analysis and statistics conveniently on your PC. With easy to use keys, this innovative product is ideal for home and professional usages. [. . . ] Press the Mode key to select to "activate" or "deactivate" the low temperature alarm. Press the Plus or Minus key to set the desired value of the low temperature alarm point. Note: · · · · The alarms allow you to set individually the high or low threshold as you require. For example, you can set the thresholds for temperature to 85°F (high) and 65°F (low), while only activating high temp alarm and deactivating low temp alarm. In this case, the alarm will not trigger when temperature is lower than 65°F yet will trigger when temp is higher than 85. 0°F. When the temperature or humidity is sensed to be out of the pre-set threshold value, the alarm will sound and the alarm icon will be present on LCD. If no key is pressed, the buzzer will beep for two minutes however the alarm signal icon will flash until the temperature or humidity is within the pre-set range again. Once an alarm is triggered, the display switches to the latest triggered temperature/humidity sensor channel. In addition, the high/ low limit icon and IN/ OUT icon is flashing as long as the alarm condition is met. If an alarm is triggered, the alarm icon will be flashing until the temperature and/or humidity is back to the conditions within the preset threshold values. The Alarm icon and the corresponding high or low alarm icons will flash once the current temperature or humidity is out of the pre-set threshold value 15 MEMORY CAPACITY The indoor weather station provides data-logging function. The temperature and humidity data are saved into the Memory of the indoor weather station at 5-minute intervals (recording one data set every five minute). The number of sets of data stored is shown at the ''mem'' display. The data-storing capacity for various numbers of remote temperature/humidity sensors used is listed below: No. of sets of temperature and humidity data stored for each transmitter and the indoor sensor ~3260 ~2510 ~2170 0 or 1 2 3 Note: · After the capacity has been reached, the first data (the oldest sets) will be overwritten by the latest one and so on. CLEARING DATA IN THE INDOOR WEATHER STATION CLEARING THE MAX/MIN TEMPERATURE AND HUMIDITY DATA OF A PARTICULAR REMOTE TEMPERATURE/HUMIDITY SENSOR CHANNEL To clear the max/min data of a remote temperature/humidity sensor channel: 1. Press the Plus or Minus key to select a remote temperature/humidity sensor channel. The maximum and minimum temperature/ humidity data and the time of record will be reset to the current value. CLEARING THE MAX/MIN TEMPERATURE AND HUMIDITY DATA OF ALL REMOTE TEMPERATURE/HUMIDITY SENSOR CHANNELS To clear the max/min data of all remote temperature/humidity sensor channels: 1. The maximum and minimum temperature/ humidity data and the time of record will be reset to the current value. CLEARING ALL STORED TEMPERATURE AND HUMIDITY DATA (FROM TEMPORARY MEMORY OF THE INDOOR WEATHER STATION) The on-going temperature and humidity data are stored at the ring buffer memory (a temporary memory area where the latest data will displace the oldest data once the memory capacity is reached). The temperature and humidity records of all temperature/humidity sensor channels (indoor and the outdoor temperature/humidity sensor channels) will be cleared. The memory display will show "mem 0000" after the data has been cleared. Note: The maximum/ minimum temperature and humidity data will not be cleared. 16 CLEARING ALL DATA AND SETTINGS OF THE INDOOR WEATHER STATION FROM THE PERMANENT MEMORY (FACTORY RESET) The factory reset needs to be launched if a malfunction of the indoor weather station occurs. Ensure that the indoor weather station is in the normal display mode, not displaying max, min, or history. [. . . ] The figure will be highlighted and you can enter in a new figure. This figure is highlighted and can be altered You may also delete a particular row of data by first highlighting it and then clicking the "Delete" icon in the menu bar. Printing the data file The Data Recorder program enables you to print the data. Click the Print button to print the currently viewed data file. 28 WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. [. . . ]