User manual LEICA SMARTTOUCH

[. . . ] Leica SmartTouchTM Manual Table of Contents Inhaltsverzeichnis Table of Contents General Instructions Safety Concept Symbols Used Safety Instructions Safety regulations (continued) Leica SmartTouchTM Introduction Installation Unpacking Assembly General Information An Overview of the Leica SmartTouchTM Encoded and Unencoded Components Leica SmartTouchTM and Leica Application Suite (LAS) Controls on the Touchscreen Calling up the Main view The "Main" View Setup and Configuration Selecting the Desired Language The "Config. " Tab Configuration of Unencoded Components Configuration of the Objective Nosepiece Registering the objective nosepiece (cont'd) Resetting to Factory Defaults Adjusting the Brightness of the Display Adjusting the Display Brightness (cont'd) Changing the Units of Measure Switching the signal tone on and off Calibrating the touchscreen Calibrating the zoom Calibrating the Zoom (cont'd) Checking the Firmware Version The "Focus/Zoom" Tab Information about the Displays Focus Settings Focus Settings (cont'd. ) Focus Settings (cont'd. ) Zoom Settings Zoom Settings (cont'd. ) Measuring with the graticule Moving the Rotary Head 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Leica SmartTouchTM Manual 2 The "Stage" Tab Modifying the travel path speed Changing the Reference Coordinates Changing the Reference Coordinates (cont'd) Changing the Coordinate System Measuring via polar coordinates The "Light" Tab Selecting the light source Control of the Leica Fluorescence Illumination Control of the Leica LED5000 CXI Control of the Leica LED3000 NVI Control of the Leica LED5000 3000 Ring Illuminator Control of the Leica TL RCI Transmitted Light Base Control of the Leica TL RCI Transmitted Light Base (cont'd) Control of the Leica LED5000 MCI Control of the Leica LED5000 RL-80/48 Ring Illuminator Control of the Leica LED5000 HDI Memory Key Assignment Information about the Memory Keys Assigning Memory Keys Assigning Memory Keys (cont'd) Memory Key Commands List 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Memory Key Commands List (cont'd) Memory Key Commands List (cont'd) Memory Key Commands List (cont'd) Memory Key Commands List (cont'd) Double Rotary Actuator Assignment Information about the Double Rotary Actuator Assigning a Function to the Knobs Assigning a Function to the Knobs (cont'd) Commands List: Rotary Knob Assigning a Function to the Toggle Button Commands List: Toggle button Commands List: Toggle Button (cont'd) Calling Up and Saving Scenarios Saving Scenarios Calling Up Scenarios Safety Measures for Focus and Stage 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Leica SmartTouchTM Manual 3 General Instructions Safety Concept Before using your Leica SmartTouchTM for the first time, please read the "Safety Concept" brochure included with your instrument. Use in clean rooms The Leica SmartTouchTM can be used in clean rooms without any problems. Cleaning Do not use any unsuitable cleaning agents, chemicals or techniques for cleaning. Responsibilities of person in charge of instrument Ensure that the Leica SmartTouchTM is operated, maintained and repaired by authorized and trained personnel only. Never use chemicals to clean colored surfaces or accessories with rubberized parts. This could damage the surfaces, and specimens could be contaminated by abraded particles. [. . . ] It is particularly suitable if you usually work at a high magnification. The "Auto" setting adapts the speed to the respective magnification. It is particularly suitable if you have to change magnification frequently. Note that: High magnification level = slow focus ­ Low magnification level = fast focus. 1. Touch the "Speed" buttons to change the setting between "Slow", "Fast" and "Auto". (Continued on next page) Before the Leica SmartTouchTM can measure the distance between the current and top position, you have to calibrate the focus. For instructions, refer to page 33. Leica SmartTouchTM Manual 38 Focus Settings (cont'd. ) Changing the reference coordinates 1. The display shows the distance between the current position and the uppermost position that can be assumed by the motorized focus. The display shows the distance Manually defining the zero point To measure the distance between two motorized focus positions, proceed as follows: 1. Move the motorized focus into the position that is to be the zero point. between the current position and the zero point defined by the user. (Continued on next page) Leica SmartTouchTM Manual 39 Focus Settings (cont'd. ) 2. Touch the button with the double arrow to define this position as the zero point. 3. The display now shows the distance to the manually set zero point. Leica SmartTouchTM Manual 40 Zoom Settings ment and the iris diaphragm. settings for the ratchet stop, measureIn the "Zoom" area, you can configure the Ratchet Switching between measurement and field of view 1. The zoom position is controlled using the "Ratchet" buttons. This changes the zoom in predefined increments ("ratchet stops"). This behavior corresponds to the ratchet stops of manual microscopes. 1. (Continued on next page) Leica SmartTouchTM Manual 41 Zoom Settings (cont'd. ) 2. Touch the circle key to use the area covered by the optional graticule (Art. Use this measuring method only if your microscope is equipped with this graticule in the eyepiece. Iris diaphragm control display. ing method are shown directly in the The effects of the selected measur- 1. Use the iris diaphragm control keys to open and close the iris diaphragm. The effects on the depth of field are shown on the Leica SmartTouchTM under "DOF" (Depth Of Field). Leica SmartTouchTM Manual 42 Measuring with the graticule measurements directly using the Leica SmartTouchTM. 10450054), you can carry out simple Using the optional graticule (Art. Zoom in on the specimen to be measured so that it fills in the small or large circle on the graticule as accurately as possible. [. . . ] Touch one of the following two symbols to select the desired rotary actuator. Press the toggle button once briefly to switch from assignment 1 to assignment 2 (and vice versa). 2. Touch the command you want to assign to the selected rotary actuator. Leica SmartTouchTM Manual 74 Commands List: Rotary Knob Name Zoom Iris Focus Fine focus Stage X+ Stage Y+ Stage XStage YTL CT TL CCIC FIM LED5000 RL-80/48 LED5000 MCI LED5000 CXI LED3000 NVI Function Changes the magnification factor (zoom) Opens and closes the iris Controls the coarse focus Controls the fine focus If the knob is moved clockwise, the motorized mechanical stage moves towards the left. If the knob is moved clockwise, the motorized mechanical stage moves towards the rear. [. . . ]