User manual LG FFH-376A

[. . . ] Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 18 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 E-3 . Remote Control - Buttons Timer setting button Sleep timer setting button Temperature adjustment buttons Mode selection buttons Fan speed adjustment buttons Energy Saver button On/Off button E-5 You have just purchased a Samsung window-type room air conditioner which should be installed by following your installation manual. Your Owner's Instructions contain much valuable information on using your air conditioner. [. . . ] The unit beeps twice. 2 If the fan speed(F1, F2 or F3) is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: The unit beeps each time you press the The air conditioner starts up in Fan mode. Mode Cool/Dry/Fan Mode Cool/Dry/Fan You can change modes at any time. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 3 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. Fan Speed 4 To control the direction of the air flow, refer to page 11. E-9 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. Remote Control Control Panel 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in the Cool mode. The unit beeps. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will begin to cool after three minutes. 2 If the temperature is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until Result: The unit beeps each time you press the / The air conditioner starts up in the Cool mode. button. 3 To adjust the temperature, press the or buttons one or more times until the required temperature is displayed. Result: Each time you press the or buttons: - The temperature is adjusted by 1°F - The unit beeps The air conditioner starts removing the excess humidity; the quality of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 11. E-10 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit. Adjust the air flow blades to the desired position by sliding them side to side. The outer air flow blades can be adjusted to control the vertical air flow direction. RECOMMENDATION E-11 The On Timer enables you to switch on the air conditioner automatically after a given time. You can select the On timer only when the air conditioner is off. Remote Control Control Panel The Off Timer enables you to switch off the air conditioner automatically after a given time. You can select the Off timer only when the air conditioner is on. Remote Control Control Panel The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after 8 hours. Remote Control Control Panel Selecting Energy Saving Mode If you wish to save energy when using your air conditioner, select the energy saving mode. 1 To select the energy saving mode, press the control or E. Saver E. Saver button on the remote Remote Control Control Panel button on the unit one or more times until the Energy Saver indicator lights up. Make sure you have about a five degree tilt backwards for proper drainage of condensation. 9 Attach the support brackets to the cabinet for adjusting the pitch. 9-1 Select the Type D support bracket position that will place the bracket near the outermost point on the window sill. Using eight Type B screws, attach the support brackets to each side of the cabinet bottom. 9-2 Thread the Type C bolts into the support brackets, making sure the cabinet maintains a slightly downward slant to the outside. 9-1 Some windows do not have sufficient window ledge on the outside edge of the window, in such cases the brackets serve no useful purpose. 9-2 Type B Screws Type C Bolts 10 Attach the window sash seal to the window. 10-2 Remove the backing from the window sash seal and attach it to the underside of the bottom of the window. 10 Window sash seal E-35 C Type 11 149CB/AW189CB (cont. ) 11 Install the cabinet in the window. 11-1 Place the cabinet into the window with the top support channel positioned just in front of the bottom sash. Top Support Channel 11-2 Pull the window down until it rests on the cabinet, just behind the top support channel. Center the cabinet, side to side, in the window and mount it to the window stool using five Type A screws. For security, always make sure the bottom channel engages onto the inside front edge of the window. If your window sill dimensions are such that this is not possible, you may need to drill three additional holes equally spaced on the bottom channel to properly secure the cabinet. [. . . ] If during in-home service repair can not be completed, it may be necessary to remove, repair and return the product. If in-home service is unavailable, LG may elect, at our option, to provide for transportation of our choice to and from a LG authorized service center. Otherwise, transportation to and from the LG authorized service center is the responsibility of the purchaser. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following, including, but not limited to: delivery and installation; damage which occurs in shipment; applications and uses for which this product was not intended; failures or problems which are caused by products or equipment not supplied by LG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of nature; incorrect electrical line voltage, fluctuations or surges; damage caused by improper or faulty installation; product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial numbers; failure to follow operating and environmental instructions that are covered and prescribed in the instruction book; customer adjustments, routine maintenance and cleaning; consumable items such as filters; use of non-LG or unauthorized parts, supplies, accessories or equipment which damage this product or result in service problems. [. . . ]