User manual LG LAC-M3600

[. . . ] · Never use solvents such as benzine or alcohol to clean the disc. Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. A section whose title has one of the following symbols is applicable only to the disc represented by the symbol. CD MP3 Audio CDs MP3 files WMA WMA files 3 Table of contents Safety note . When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. [. . . ] Perform the same operation on the other side and pull the unit out from the mounting sleeve. A ISO-DIN Installation 1 3 2 4 5 6 1 2 3 4 5 6 Slide the unit into the ISO-DIN frame. Install the control panel to the unit. Control panel 8 Connection diagram Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits. B 1 2 1 2 3 4 3 4 5 6 5 6 7 8 7 8 To Speaker To Vehicle A B A A A A A A A 2 r (Optional) A PHONE MUTE (ORANGE) 8 GROUND(-) (BLACK) 6 DIMMER SWITCH DIMMER (PINK) 7 IGNITION SWITCH TO IGNITION (RED) 4 TO BATTERY(+) (YELLOW) 5 POWER ANTENNA (BLUE) 1 AMPLIFIER (Optional) BATTERY 1 2 3 C REMOTE ON (BLUE/WHITE) POWER Antenna 4 5 CONTROL RELAY 6 7 8 B B B B B B B B 1. 8. Violet : Rear Right + Violet/ Black Stripe : Rear Right ­ Gray : Front Right + Gray / Black Stripe : Front Right ­ White : Front Left + White/Black Stripe : Front Left ­ Green : Rear Left + Green/ Black Stripe : Rear Left ­ 9 Connection C Speaker Connections A From antenna B To the wiring of the vehicle colors of leads. 1 2 3 4 5 6 7 8 · BLACK · ORANGE · PINK L REAR : This lead is for the ground connection. : This lead is for connection to the power supply terminal when the ignition switch is set to ACC. : This lead is for connection to the battery (back-up) terminal from which power is always supplied. : This lead is for the power antenna connection. · RED · YELLOW L FRONT · BLUE R FRONT · BLUE/WHITE : This lead is for the remote amplifier on connection. R REAR Connecting to Auxiliary Equipment (Optional) Connect the AUDIO OUTPUT jack of this unit to the AUDIO INPUT jack of the Auxiliary Equipment. FL (Front Left) FR (Front Right) RL (Rear Left) RR (Rear Right) To AUDIO OUT To AUDIO IN To AUDIO IN Amplifier 10 Basic operation Turning the unit on Press MUTE/PWR (POWER/ on the remote control) or any other button. Note When you insert the CD in the CD slot, the unit turns on. Turning the unit off Press and hold MUTE/PWR (POWER/ on the remote control). Insert a disc 1 2 Press to open the control panel. Draws the disc, and starts playback automatically. Eject a disc Press to open the control panel. When the disc is ejected by pressing during playback, it will be loaded automatically after 10 seconds unless you pull out disc from the unit. Selecting a source Press SOURCE repeatedly to select a source. TUNER CD AUX TUNER. . . Note You cannot select a source if a CD is not inserted. Adjusting the volume Rotate MUTE/PWR (Press VOLUME on the remote control) to adjust the sound level. Note When you turn the unit off, the current volume level is automatically memorized. Whenever you turn the unit back on, it will operate at the memorized volume level. Mute 1 2 Press MUTE/PWR (POWER/ To cancel it, press again. · When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Auto search memory This function lets you automatically store the 6 strongest broadcast frequencies. The six strongest broadcast frequencies will be stored under preset button 1~6 in the order of their signal strength. To cancel, press U/AS. 2 To scan the preset stations Press u/PS. To cancel, press u/PS. To tune in the preset stations Press BAND to select the desired band and press the desired preset button 1~6. The preset station of the preset button 1~6 is displayed and the preset station is received. 15 RDS operation RDS Display options In normal RDS operation the display will indicate the station name. Pressing DISP enables you to cycle through the various data types in the following sequence: CT t FREQUENCY t PTY t RT t PS · CT (Time controlled by the channel) · PTY (Programme type recognition) · RT (Radio text recognition) · PS (Programme Service name) · PI (Programme Identification) · AF (Alternative Frequencies for the actual programme) · TP (Traffic programme Identification) · TA (Traffic Announcement Identification) PTY (Programme Type) function To select a certain program type out of the reception band, the following procedure can be used. Music group t Speech group t Search off 3 Press one of preset buttons 1-6 Each time this button is pressed, the display mode changes as follows. Speech group News, Affairs, Info Sport, Educate, Drama Culture, Science, Varied Weather, Finance, Children Social, Religion, Phone In Travel, Leisure, Document Note RDS is only available for FM reception. TA (Traffic Announcement) function TA reception allows the unit to switch temporarily to a Traffic Announcement from the current source (another FM station, CD, or other connected components). To switch the TA (Traffic Announcement) function on or off, press TA/PTY. · TA ON Traffic programs and announcements can be automatically received using TP/TA features. · TA OFF Traffic programs and announcements can not be received by using TP/TA features. 16 CD/MP3/WMA operation Playing an Audio CD and MP3/WMA Disc The unit can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs. [. . . ] Press DISP repeatedly during MP3/WMA/CD TEXT file playback. To go to a particular quickly (+10/-10 steps) (If there is no folder or one folder. ) MP3 WMA U u Press U/AS (U on remote control) to skip to the next 10 track, and press u/PS (u on remote control) to skip to the previous 10 track. To skip to the next or previous folder (If there are more than two folders. ) MP3 WMA U u Press U/AS (U on remote control) to skip to the next folder, and press u/PS (u on remote control) to skip to the previous folder. Note Time display appearing on the display part when playing VBR file may vary and there may be some difference from actual time (both progress time and VBR are displayed at the same time when playing file). 18 AUX operation Playing an Auxiliary Equipment You can connect Auxiliary Equipment to this unit. Connect one to the external device jack using the line input cable (not supplied), and the other to the AUX input jack on the control panel. Auxiliary input Line input cable MP3 Player, etc 1 2 3 Press SOURCE to select the AUX as source. Turn on the connected Auxiliary Equipment and start playing the source. Adjust the volume. Note · Before operating the Auxiliary Equipment using the following procedure, select the external input correctly. [. . . ]