User manual LG LAC6700R

[. . . ] Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. DO NOT STARE INTO BEAM. 2 Safety note · A defective or soiled disc inserted into unit can cause sound to drop out during playback. on the surface. Do not expose the disc to direct sunlight or excessive heat. 8 cm This unit cannot play 8cm disc (use 12cm disc only). · Clean the disc before playback. [. . . ] When the disc is ejected by pressing during playback, it will be loaded automatically after 10 seconds unless you pull out disc from the unit. Selecting a source Press SOURCE repeatedly to select a source. TUNER CD USB TUNER. . . Note You cannot select a source if is not ready. Adjusting the volume Rotate MUTE/PWR (Press VOLUME on the remote control) to adjust the sound level. Note When you turn the unit off, the current volume level is automatically memorized. Whenever you turn the unit back on, it will operate at the memorized volume level. Mute 1 2 Press MUTE/PWR (POWER/ To cancel it, press again. on the remote control) to cut the sound. Checking the clock You can see the clock pressing DISP (DISP. on the remote control). 11 Basic operation Changing the general settings 1 2 3 Press MENU (Press and hold MENU/SEL on remote control) so that one of menu items appears. AF ON t REG ON t TA ALARM t PI SOUND t DEMO ON t BEEP 2ND Rotate MUTE/PWR clockwise or unclockwise to select one of the settings specified belows. (Press VOLUME on the remote control. ) Press and hold MENU (MENU/SEL on remote control) to finish the setting. Once you select a USER mode and then make an adjustment, it automatically stored for the currently selected USER mode. Refer to the "Adjusting the sound level" on the page 14. 13 Basic operation Adjusting the sound level 1 Press SEL (MENU/SEL on the remote control) repeatedly to select the mode you want to adjust from volume, bass, middle, treble, balance and fader. Decrease the level of the front speaker(s). 2 Turn left Decrease the volume level. Decrease the level of the rear speaker(s). VOL BAS MID TRB BAL FAD Note When EQ, BRB or XDSS+ is set to "Off", you can adjust the sound level (BAS, MID, TRB) settings. XDSS+ (Extreme Dynamic Sound System) 1 2 Press and hold EQ/XDSS/BRB. XDSS+ t BRB (TBB t 3D t SBB) XDSS+ : Improve the treble, bass sound. BRB (Bass Reverb Blaster) 1 2 3 Press and hold EQ/XDSS/BRB. · TBB (Turbo-Bass Blaster) : Improve the bass sound to make it spectacular. · 3D (3D-TremD Blaster) : Positions audio effects real time in 3D space. · SBB (Sound field Boost Blaster) : Extremely wide stereo imaging and improved low frequency bass. 14 Radio operation Listening to radio stations 1 2 3 Press SOURCE to select the tuner. on the remote control) until "MANUAL" appears, and then press it repeatedly. The frequencies move up or down step by step. Storing and recalling broadcast frequencies You can easily store up to 6 broadcast frequencies for later recall at the touch of a button. The number you have pressed will flash in the preset number indicator and then remain lit. The next time, you press the same preset button, the radio station frequency is recalled from the memory. 4 Note · Up to 18 FM stations, 6 for each of three FM bands and 6 MW(AM) stations can be stored in the memory. · When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Auto search memory This function lets you automatically store the 6 strongest broadcast frequencies. The six strongest broadcast frequencies will be stored under preset button 1~6 in the order of their signal strength. To cancel, press U/AS. 2 To scan the preset stations Press u/PS. [. . . ] · If the connected device is not supported, "USB ERROR1" or "USB ERROR2" will appear on the display window. · Do not guarantee USB devices that adopted the OTG technology. 19 Troubleshooting Symptom Power doesn't turn on. Rectify the problem that caused the fuse to blow, and then replace it. Turn the unit off and then on. Noise and other factors are causing the built-in microprocessor to operate incorrectly. [. . . ]