User manual LG LSM304H-1

[. . . ] Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) and Power Cord (Depending on the country) Lan cable and EMI Core (These items are not included for all models. ) IMPORTANT This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, LAN cable) with ferrite cores to maintain standard compliance for the product. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. [. . . ] Disposal of this product must be carried out in accordance to the regulations of your local authority. A3 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it "click". Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Stand Base 4. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. The product may fall and get damaged or injure your foot. A4 Connecting the Display Disassembling the stand 1. Place the monitor face Down on the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 4. Pushing the PUSH button, Take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A6 Connecting the Display Using the Computer NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 1. A Connect D-sub(RGB Analog) Cable (PC) B Connect D-sub(RGB Analog) Cable (Mac) Analog signal X-PORT D-sub Wall-outlet type A B Mac adapter (This item must be purchased separately. ) For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. NOTE ` Self Image Setting Function'?Restrictions : Using this network monitor for the following purposes may cause screen disruption or slower PC operation. Games Color setting: Image quality may vary depending on the X550 card, so it is recommended to execute "White Balance" when using the product as a network monitor after connecting a LAN cable for the first time. If you use the monitor with a X-PORT input, image quality and resolution may be poorer than with a D-sub input. ( Only 16 bit color is supported for X-PORT input. ) A10 Control Panel Functions Front Panel Controls MENU AUTO/SET SOURCE VOLUME Control Function Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. When the icon you want becomes highlighted, press the AUTO/SET Button. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A13 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu PICTURE Sub-menu BRIGHTNESS CONTRAST GAMMA COLOR PRESET RED GREEN POSITION TRACKING BLUE HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS SETUP LANGUAGE OSD HORIZONTAL A X Reference To adjust the brightness, contrast and gamma of the screen To customize the color of the screen sRGB 6500K 9300K To adjust the position of the screen To improve the clarity and stability of the screen POSITION VERTICAL To customize the screen status for a user's operating environment WHITE BALANCE POWER INDICATOR FACTORY RESET FLATRON F ENGINE MOVIE INTERNET USER NORMAL DEMO ACE RCM To select or customize desired image settings : Adjustable A : D-SUB Input X : X-PORT Input NOTE The order of icons may differ depending on the model (A14~A19). A14 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter Menu Name : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A15 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. [. . . ] G Is the power indicator flickering? · Press the Power button. · If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. · Try to turn on the PC. G Do you see an "OUT OF · This message appears when the signal from the PC (video card) is out of horizontal or vertical RANGE" message on frequency range of the display. 'Specifications' section of this manual and configure your display again. · This message appears when the signal cable between your PC and your display is not connected. [. . . ]