User manual LG LST-5402P

[. . . ] Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] · Extremely hot or cold places (operating temperature -10 °C - 50 °C, however, we recommend that the unit be used within a temperature range of 0 °C - 45 °C) · Damp or dust place · Places exposed to rain · Places subject to strong vibration · Close to generators of powerful electromagnetic radiation such as radio or TV transmitters. P Handling of the unit Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock. Handling of the unit · Remove dust or dirt on the surface of the lens with a blower. · Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent, then wipe dry. · Avoid the use of volatile solvents such as thinners, alcohol, benzene, and insecticides. They may damage the surface finish and/or impair the operation of the camera. Operating and storage location Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations. 8 Part Names and Functions a Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately) . b Flange-back adjustment lever c Camera installation bracket The bracket can be fixed at the top or bottom of the camera. (page 20) a - bc , 9 Part Names and Functions d Power input terminal AC 24 V or DC 12 V input terminal P e External Device Connectors · D&N Connect the external switch to set the D&N function manually. Alarm Output Terminal (ALARM OUT/COM) Connect to the alarm input of an external device. or button C 2. Note: The setup menu will be disappear after save the current setting value. 22 Camera Identification Settings Camera Identification Setting You can use the camera identification (CAMERA ID) to assign a number to the camera. Use or to select a CAMERA ID (OFF, 1-255). 23 Exposure Settings You can set the exposure options using the EXPOSURE menu. Press button and the EXPOSURE menu appears. E WDR/BLC setting Use WDR/BLC option to set the options for BLC or WDR camera. Use · · · or button to select a mode then press . WDR LIMIT: LOW y MIDDLE y HIGH BLC LIMIT: LOW y MIDDLE y HIGH BLC: Set the BLC limit. AREA SETTING: Use or button to select a area or button to select a ON or OFF. Press then use to exit the Area setting menu. 24 Exposure Settings GRAY SCALE: Use or button to select a gray scale. USER SCALE: Use level. (5 level) or button to select a bright Brightness setting You can set the brightness level. Use or button to set the bright level. AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images lighter. (OFFy LOWyMIDDLEyHIGH) 25 Exposure Settings SHUTTER (Shutter Speed) setting 1. (AUTOy OFF y A. FLK y 1/160 ~ 1/90000 y x512~x2) W SENS-UP setting If pictures are not clear due to darkness, use for increase the sensitivity of picture. [. . . ] to select an option then use or button to adjust or Use the option. · · · · HEIGHT: Enlarge or decrease the vertical size of the mask. MOVE Y: Moves vertical position of the mask. 6. Use [SENSITIVITY] option to obtain the optimum detection level. 30 3D-DNR Setting 1. If pictures are not clear due to bightness, use for reduce the noise of picture. [. . . ]