User manual LG LW5200R

[. . . ] The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number (the right side) and the indoor air will become cooler. The 5 or 6 position (the middle position of arc) is a normal setting for average conditions. For Normal Cooling- Select High Cool or Med Cool with the OPERATION knob at the midpoint of THERMOSTAT/TEMPERATURE knob. For Maximum Cooling- Select High Cool with the OPERATION knob at the highest number available on your THERMOSTAT/TEMPERARURE knob. [. . . ] For Quieter & Nighttime Cooling- Select Low Cool with the OPERATION knob at the midpoint of THERMOSTAT/TEMPERATURE knob. OPERATION HIGH ( ) Cool, LOW ( ) Cool provide cooling with different fan speeds. FAN ( ) provides air circulation and filtering without cooling or heating. NOTE: If you move the switch from the cool(or the heat) setting to off or to a fan setting, wait at least 3 minutes before switching back to a cool(or heat) setting. Cooling Descriptions THERMOSTAT (TEMPERATURE) The THERMOSTAT/TEMPERATURE is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. The temperature is selected by turning the THERMOSTAT/ TEMPERATURE knob to the desired position. For Normal Cooling- Select HIGH Cool with the OPERATION knob at the midpoint of the THERMOSTAT/TEMPERATURE knob. For Maximum Cooling- Select HIGH Cool with the OPERATION knob at the clockwise available on the THERMOSTAT/TEMPERATURE knob. For Quieter & Nighttime Cooling- Select LOW Cool with the OPERATION knob at the midpoint of the THERMOSTAT/ TEMPERATURE knob. Heating Descriptions For Normal Heating- Select HIGH heat with the OPERATION knob at the midpoint of the THERMOSTAT/TEMPERATURE knob. For Maximum Heating- Select HIGH heat with the OPERATION knob at the counterclockwise available on the THERMOSTAT/TEMPERATURE knob. For Quieter Heating- Select LOW heat with the OPERATION knob at the midpoint of the THERMOSTAT/TEMPERATURE knob. HEATER LAMP At the heating operation, the lamp is lighted. When the frost settles on the heat exchanger of the outside, defrosting is made automatically and the lamp is unlighted. After defrosting, the heating operation begins again. AUTO SWING Auto swing switch controls the horizontal air direction by air swing system (not on all models). Rinse and gently shake the water from the filter and let it dry before replacing it. CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. Drainage In humid weather, excess water may cause the BASE PAN to overflow. To drain the water, remove the DRAIN CAP and secure the DRAIN PIPE to the rear hole of the BASE PAN. To remove the condensed water, you can install the drain pan as below. Install the drain pan to the right corner of the cabinet with 4 screws. Connect the drain hose to the outlet located at the bottom of the drain pan. You can purchase the drain hose or tubing locally to satisfy your particular needs. (Drain hose is not supplied). -8- Features Learning parts name prior to installation will help you understanding the installation procedure. Features 1. HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER) Installation Instructions Select the Best Location To prevent vibration and noise, make sure the unit is installed securely and firmly. Install the unit where the sunlight does not shine directly on the unit. There should be no obstacle, such as a fence or wall, within 50cm from the back of the cabinet because it will prevent heat radiation of the condenser. [. . . ] There should be no obstacle, such as a fence or wall, within 50cm from the back of the cabinet because it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. Install the unit a little obliquely outward not to leak the condensed water into the room (about 10 ~ 15mm or 1/4 bubble with level). CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 9. [. . . ]