User manual LG LWG09

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. [. . . ] Result: You can control all the functions on your air conditioning unit directly from your seat, using the remote control. 3 E-7 Cooling Your Room Remote Control Control Panel You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. 1 If necessary, press the (On/Off) button. The operating mode indicator (COOL, FAN or HEAT) on Result: the unit comes on. The air conditioner starts up in the mode selected when the unit was last used. air Theunit conditioner is fitted with a protection mechanism to prevent the from being damaged when it is started immediately after being: Plugged in Stopped It will start up automatically after about three minutes. 2 If the COOL indicator is not lit up on the unit: Press the button on the remote control or Press the MODE button on the unit one or more times until the COOL indicator lights up The unit beeps each time you press MODE. Result: The air conditioner starts up in Cool mode. 3 You can change modes at any time. To adjust the temperature, press the or button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the or button on the unit one or more times until the required temperature is displayed. Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Med Low Result: Each time you press a button, the unit beeps. 5 E-8 To control the direction of the air flow, refer to page 11. Heating Your Room ENGLISH You must select the Heat mode if you wish to heat your room to a specific temperature. or on the remote control or unit (The air conditioner operates in the mode selected when the unit was last used. ) E-13 Setting the Sleep timer The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of 8 hours. Remote Control Control Panel 1 2 If you wish to switch the unit off at a specific time, refer to page 13. Press the or Press the Result: button on the remote control button on the unit until the SLEEP indicator lights up. The "SLEEP" passes through the control panel for about " will be displayed. 15 seconds and the " The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. The air conditioner will be controlled as illustrations below. Cooling When the temperature has been increased by 1°C (after 1 hour), it is maintained for 7 hours. Set TEMP. Start time 1hr Stop time 8hr Heating The temperature is decreased by 1°C after 1 hour. When it has been decreased by 2°C (after 2 hour), the temperature is maintained for 6 hours. To Cancel the Sleep Timer To cancel the timer, press: on the remote control. The air conditioner operates in the mode selected last. E-14 Operating Recommendations ENGLISH Here are a few recommendations that you should follow when using your air conditioner. Topic Heating performances Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. [. . . ] Check that the operating mode indicator(COOL, FAN or HEAT) on the unit is lit up; if necessary press (On/Off) on the remote control or unit. Check that you are close enough to the unit (seven metres/yards or less). Check that you are pointing the remote control at the remote control sensor on the unit. Dust may be blocking the air filter; refer to page 17 or 18 for cleaning instructions. [. . . ]