User manual LG MG-583MC

[. . . ] If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 1 way stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 3. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. Important This illustration depicts the general model of connection. The product may fall and get damaged or injure your foot. 5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2 way stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Press the button as shown, and pull the stand body up. Pr es s 3. After pull the stand body up, take the monitor up carefully and face the front side. (Once you pull the stand body up, please keep pressing the button. If you don't press the button, it will damage the product. ) When limited tilt degree, the button is not working, pull stand body up or down a little. 6 Connecting the Display 4. If you want to use the stand base, pull the stand body down. (Once you pull the stand body down, please keep pressing the button. If you don't press the button, it will damage the product. ) 5. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 6. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. The product may fall and get damaged or injure your foot. 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. DVI-D input PHASE Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu 17 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. Use this function to set the power indicator on the front side of the monitor to ON or OFF. If you set ON at any time, the power indicator will automatically be turned on. Use this function to set the control key indicator on the front side of the monitor to ON or OFF. If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image. Activate this function when white and black colors are present in the screen. Restore all factory default settings except "LANGUAGE. " Press the , buttons to reset immediately. POWER INDICATOR Exit : Exit BUTTON : Decrease INDICATOR : Increase : Select another sub-menu : Restart to select sub-menu WHITE BALANCE FACTORY RESET NOTE If this does not improve the screen image, restore the factory default settings. This function will be enabled only when the input signal is an analog signal. 18 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the SMART+ Button, then the main menu of the OSD appears. Menu Name Icons Submenus Exit Move Restart to select sub-menu Button Tip NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. 19 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If select on, it automatically controls the brightness of display to best suit the surrounding working environment, providing the optimal viewing condition and maximized user convenience. [. . . ] If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. · Press the AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. [. . . ]