User manual LG TCH-M1000R

[. . . ] · Never use solvents such as benzine or alcohol to clean the disc. Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. A section whose title has one of the following symbols is applicable only to the disc represented by the symbol. CD Audio CDs MP3 MP3 files WMA WMA files MP3/WMA Disc compatibility with this unit is limited as follows: 1. Sampling Frequency / 8 - 48kHz (MP3) 22. 05 - 48kHz (WMA) Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA) CD-R/CD-RW file system should be "ISO 9660" If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example "Direct-CD" etc. , it will not be possible to playback MP3/WMA files. We recommend that you use "Easy-CD Creator" which creates an ISO9660 file system. Customers should also note that permission is required in order to download MP3/WMA files and music from the Internet. [. . . ] · Do not drop the control panel or otherwise subject it to strong impact. 2 1 · Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. 4 Control panel 1 2 3 4 5 6 EJECT Z Alternative frequency [AF(REG)] Traffic Announcement [TA] Remote Sensor - Optional · Volume · [MUTE] · Power [PWR] · Auto Store [AS] · Preset Scan [PS] · Equalizer [EQ] 7 8 9 10 11 12 13 14 DISC SLOT · Skip / Search B[ + · Seek/ Tune B[ + Display [DISP] Release Select [SEL S ] · Skip / Search - [b · Seek/ Tune - [b Preset Station [1-6] · MP3 Track +10/-10 [F+/F-] MP3 WMA · Folder Up/Down [F+/F-] MP3 WMA 15 16 17 18 19 Shuffle [SHF] Repeat [RPT] Intro Scan [SCAN] Play/Pause B X Extreme Dynamic Sound System [XDSS] 20 [BAND] 21 Programme Type [PTY] 22 SOURCE [SRC S] Remote control (optional) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 8 1 2 3 4 5 6 7 Power [POWER] / Mute Select [SEL] Source [SRC] Play / Pause B/X Intro Scan [SCAN] Shuffle [SHF] · MP3 Track +10 MP3 WMA 9 10 11 12 13 14 15 · Folder Up [F+] MP3 WMA · CD Skip / Search ?m m · Seek / Tune ?m m [BAND] Volume Up / Down Number [#] Repeat [RPT] Preset Station [1-6] Number [0 -9] · CD Skip / Search M M?16 Display [DISP. ] 17 · MP3 Track -10 MP3 WMA · Folder Down [F-] MP3 WMA 5 Battery Installation 1 2 3 Pull out the battery holder with a sharp product like a ball point pen. Push the battery holder back into its original position. Note · Use only one CR2025 (3V) lithium battery. · Remove the battery if the remote control is not used for a long period of time. · Do not store the battery with metallic materials. Installation Basic Installation Bend the claws according to the thickness of the dashboard Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. Install the unit into the installation sleeve. Control panel Removing the existing receiver unit A If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed. Perform the same operation on the other side and pull the unit out from the mounting sleeve. ISO-DIN Installation 1 2 3 4 5 6 Slide the unit into the ISO-DIN frame. Install the control panel to the unit. 4 5 6 3 1 2 Control panel 6 Connection diagram Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits. B 1 2 1 2 3 4 3 4 5 6 5 6 7 8 7 8 To Speaker To Vehicle B (Optional) r (Optional) A A A A A A A A A 2 PHONE MUTE (ORANGE) 8 GROUND(-) (BLACK) 6 DIMMER SWITCH DIMMER (PINK) 7 IGNITION SWITCH TO IGNITION (RED) 4 TO BATTERY(+) (YELLOW) 5 POWER ANTENNA (BLUE) 1 AMPLIFIER (Optional) BATTERY 1 2 3 C REMOTE ON (BLUE/WHITE) POWER Antenna 4 5 CONTROL RELAY 6 7 8 B B B B B B B B 1. 8. Violet : Rear Right + Violet/ Black Stripe : Rear Right ­ Gray : Front Right + Gray / Black Stripe : Front Right ­ White : Front Left + White/Black Stripe : Front Left ­ Green : Rear Left + Green/ Black Stripe : Rear Left ­ 7 A From antenna B To the wiring of the vehicle colors of leads. · BLACK: · ORANGE: · PINK: · RED: · YELLOW: · BLUE: This lead is for the ground connection. This lead is for connection to the power supply terminal when the ignition switch is set to ACC. This lead is for connection to the battery (back-up) terminal from which power is always supplied. · When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Auto search memory This function lets you automatically store the 6 strongest broadcast frequencies. The six strongest broadcast frequencies will be stored under preset button 1-6 in the order of their signal strength. To cancel, press AS/PS. 2 To scan the preset stations Press AS/PS. To cancel, press AS/PS. To tune in the preset stations Press BAND to select the desired band and press the desired preset button 1-6 (preset button 1-6 on the remote control). The preset station of the preset button 1-6 is displayed and the preset station is received. 12 RDS operation RDS Display options In normal RDS operation the display will indicate the station name. Pressing DISP enables you to cycle through the various data types in the following sequence: CT t FREQUENCY t PTY t RT t PS · CT (Time controlled by the channel) · PTY (Programme type recognition) · RT (Radio text recognition) · PS (Programme Service name) · PI (Programme Identification) · AF (Alternative Frequencies for the actual programme) · TP (Traffic programme Identification) · TA (Traffic Announcement Identification) PTY (Programme Type) function To select a certain program type out of the reception band, following procedure can be operated. 2 After, pressing PTY button one by one activated as selecting each mode. music grouptspeech grouptsearch off 3 Press one of the PRESET (1-6) button shortly. Each time this button is pressed, the display mode changes as follow. No 1. 6. Speech group News, Affairs, Info Sport, Educate, Drama Culture, Science, Varied Weather, Finance, Children Social, Religion, Phone In Travel, Leisure, Document TA (Traffic Announcement) function TA reception allows the unit to switch temporarily to a Traffic Announcement from the current source (another FM station, CD, or other connected components). · TA ON Traffic programs and announcements can be automatically received using TP/TA features. [. . . ] on remote control) for about 1 second during playback and then release at the point you want. Intro scan The first 10 seconds of each tracks/files (SCAN) or each files in the current selected folder ( SCAN) on the disc are played. ­ SCAN or SCAN disappear from the display window and the intro scan is cancelled. 2 Repeat The current selected tracks/files (1 RPT) or folder ( 1 2 3 RPT) on the disc is played repeatedly. ­ 1 RPT or RPT disappear from the display window and the repeat mode is cancelled. 14 Shuffle All of the tracks/files (SHF) or the current selected folder ( SHF) on the disc is played randomly. ­ SHF or SHF disappear from the display window and the random playback is cancelled. Note During random playback, if you press - [b (?m m on remote control), you won't go back to the previous track. CD TEXT / ID3 TAG When playing a disc containing information, you can see the CD TEXT/ID3 TAG information. [. . . ]