User manual LG V692WK

[. . . ] All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER, WARNING, or CAUTION. These words mean: DANGER You will be killed or seriously injured if you don't follow instructions. you don't follow instructions. WARNING You can be killed or seriously injured if CAUTION Indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate injury, or product damage only. All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. 36 Introduction Important Safety Instruction To reduce the risk of fire, electric shock, or injury to persons when using your product, basic safety precautions should be followed, including the following. [. . . ] 45 Introduction Important Safety Instruction Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. The refrigerant and insulation blowing gas used in the appliance require special disposal procedures. When disposal, please consult with service agent or a similarly qualified person. This appliance contains a small amount of isobutane refrigerant (R600a), natural gas with high environmental compatibility, but it is also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 1m2 in size for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification plate inside the appliance. · To remove ice cubes, hold the tray at its ends and twist gently. Ice Making Tip To remove ice cubes easily, run water on the tray before twisting. Defrosting Defrosting takes place automatically. The defrosting water flows down to the evaporating tray and is evaporated automatically. 53 Operation Water Dispenser Features Install · Please assemble the VALVE ASSEMBLY after correctly adjusting it with a DOOR HOLE. 54 Operation Filling of WATER TANK 1. After turning the HANDLE Tank backward with the WATER TANK installed at the DOOR, Open the CAP TANK (SMALL) and then fill water using a kettle etc. * Fill water while watching a sight glass on the front of the WATER TANK. After filling spring water, fix the HANDLE TANK at a proper position. Drinking 1. If pressing the Pad, water inside of the Dispenser is supplied. 3. If slowly removing a cup from the Pad, water will not fall down. CAUTION Do not use other beverage (milk, juice, carbonated beverage etc) than spring water. Especially beverage including grain must not be used (may result in failure). 55 Suggestions on food storage Storing Food Storing Food · Do not store food which goes bad easily at low temperature, such as banana, and melon. Placing hot food in the fridge-freezer could spoil other food, and lead to higher electric bills. This prevents moisture from evaporating, and helps food to keep its taste and nutrients. [. . . ] Loosen the bolt 20 of the Hinge Middle 21 , remove the Hinge Middle 21 , and lift up the freezer door 30 to separate it. (When separating the refrigerator door, separate the bush 35 together. )Separate the hinge cover 24 and set it on the separated part of middle hinge 21 . After unscrewing the screw connected to the bottom cover 25 connect the cover cap 26 on the right side. Loosen the pin 29 in counterclockwise direction and move to the hole on the left side to tighten in clockwise direction. [. . . ]