User manual LG WD-1019BD

[. . . ] · Plastic parts may be deformed or damaged, and an electric shock or a fire may take place. WARNING There might be serious injury or fatal accident when you violate this instruction. Do not bend the power supply cord by force or press it with heavy things. Do not install the washer nearby electric implement or don't put a candle light or cigarette light on the washer. During operation, do not put your hands or metal materials under the washer. [. . . ] Ventilate immediately without touching the power plug if gas is leaking. · An electric shock or a fire may take place if it catches flame. If the washer makes strange noise, smell or smoke, unplug it promptly and call service agent. When cleaning, don't spray water to the parts of the washer directly. Also an electric shock or fire may take place Don't use several appliances together with an outlet. Don't press the button with an awl or pin. · An electric shock or a fire may take place. Child-Lock function: This is a device to protect children from being accidentally hurt while playing with the washer. How to start the Child-Lock function: - Press the "Power" button to go to an initial washing mode. - By pressing "Start/Hold" button, you start washing and in case Child Lock function is needed during the laundry - Push the "Course" button and get the function started. (Note: You cannot perform the function without the "Power" button on. ) In the event that you would like to modify the Child-Lock function, "L" signal flashes in the "signal window showing the rest of the set time" every two seconds, which means it is locked and indicates how much time is left until the function is released. To release the function of Child-Lock: - In case the "Child-Lock" is programmed, press both the "Function" and "Course" buttons in sequence. 2 FILTER LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE(HOT) WATER SUPPLY HOSE (COLD) DRAIN-HOSE (PUMP) Lint will be collected in the filter during washing. DETERGENT BOX FABRIC SOFTENER DISPENSER SPIN BASKET POWER CORD DESCRIPTION OF PARTS The User's Manual is for common use. Make use of the User's Manual depending upon your washing machine model. 3 BLEACH INLET PULSATOR GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. FRONT CONTROL PANEL WATER DRAIN HOSE ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. SOUND ABSORPTION PANEL For more details, see control panel of your washing machine. When the FUNCTION button is pressed during working, the rinse times can be changed to between 1 and 5 times in duration. 6 The User's Manual is for common use. Make use of the User's Manual depending upon your washing machine model. ENVIRONMENT Leave some space Maintain at least 10cm between the washer and the wall. If the washer is placed on an uneven or weak surface, noise or vibration occurs. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. INSTALLATION & MAINTENANCE LEVELLING · If the washer is not leveled with the ground, it makes the machine tremble more or be out of order. So, make sure that the washer is leveled properly. SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. · Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. Adjust the side horizontally first and the front in same direction next. If the thread is not within the limit, adjust the height of the legs. · Adjust the legs on feet for levelling . Connect the other end of the water supply hose to the inlet water valve at the back of the washer. [. . . ] Pull in the filter and connect the hose to the inlet water valve tightly. Note to tighten up the connector. CLEANING THE FILTER NET Clean the filter net often to keep the washer clean. 1. Close the cover and insert the lower part of the filter in the basket first and then push the filter with "click" sound . 1. Remove dirts and rotate the filter clockwise until it locks in position. [. . . ]