User manual LG WD-80158TP

[. . . ] / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal. ) Use this button for auto adjustment. AUTO button MENU button [ ] Opens the OSD menu. / This light glows blue during normal operation, and blinks blue once as the monitor saves your adjustments. Power button [ ] / Power indicator See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Rear (The configuration at the back of the monitor may vary from product to product. ) DVI Connect the DVI terminal of your monitor to your computer using a DVI cable. [. . . ] (The locking device has to be purchased separately. ) For using a locking device, contact where you purchased it. USB connection terminal DOWN (USB downstream port): Connect the DOWN port of the USB monitor and a USB device with the USB cable. To use DOWN (Downstream Port), you have to connect the UP (Upstream Cable ) to the PC. USB connection terminal UP (USB upstream port): Connect the UP port of the monitor and the USB port of the computer with the USB cable. Make sure to use the USB cable supplied with this monitor to connect the monitor's UP port and your computer's USB port. See Connecting the Monitor for further information regarding cable connections. Connecting the Monitor Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Connect the monitor to the Macintosh computer using the DVI connection cable. If your monitor displays an image, installation is completed. Changing the Stand and Installing the Hoods Sliding Stand Stand Stopper Swivel stand Using ( ), You can swivel the monitor left and right at an angle of 330 ° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. Tilt angle Using ( angle. ), You can adjust the tilt angle forward and backward for the most comfortable viewing Removing the base 1. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove two screws ( ) and then remove the Stand from the LCD monitor. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad. A. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor. For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. The screen shows strange colors or just black and white. Have you locked the On Screen Display (OSD) Menu to prevent changes?Is the screen displaying only one color as if looking at the screen through a cellophane paper?Have the screen colors become strange after running a program or due to a crash between applications?Has the video card been set properly? Set the video card by referring to the video card manual. (Refer to the Preset Timing Modes). The screen suddenly has become unbalanced. Have you changed the video card or the driver?Have you adjusted the resolution or frequency to the monitor? The screen can be unbalanced due to the cycle of the video card signals. Is the frequency properly adjusted when checking the Display Timing on the menu?Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product. ) There are only 16 colors shown on the screen. Windows ME/2000/XP: Set the colors properly at the Control Panel Display The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Settings. [. . . ] Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions. Check the following items if there is trouble with the monitor. 1. Check if the power cord and the video cables are properly connected to the computer. (If it does, request an a service for the main board of the computer. ) 3. [. . . ]