User manual LG WD-8023FB

[. . . ] Don't' install it in the area with moisture or outdoor where it has rain or snow · An electric shock or a fire may take place. If there is dust or water on the power supply plug and its connected part, please remove it completely. · If your kid falls into the washer, his life could be in danger. Ventilate immediately without touching the power plug if gas is leaking. [. . . ] When cleaning, don't spray water to the parts of the washer directly. Also an electric shock or fire may take place Don't use several appliances together with an outlet. Don't press the button with an awl or pin. · An electric shock or a fire may take place. Do not bend the power supply cord by force or press it with heavy things. Do not install the washer nearby electric implement or don't put a candle light or cigarette light on the washer. Do not disassemble, repair or remodel it recklessly. · When you need to repair it, please call service agent. During operation, do not put your hands or metal materials under the washer. Stay away from the washer when the bottom of the washer sinks into the water. Do not put laundry stained with gasoline, benzene, or alcohol in the washer, and keep the materials away from the washer. If it does not stop within 15 seconds after you open the lid, call service agent immediately. · An electric shock or a fire may take place. 2 FILTER WATER SUPPLY HOSE(HOT) LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE (COLD) The User's Manual is for common use. Make use of the User's Manual depending upon your washing machine model. DRAIN-HOSE (PUMP) Lint will be collected in the filter during washing. DETERGENT BOX DESCRIPTION OF PARTS FABRIC SOFTENER DISPENSER SPIN BASKET POWER CORD BLEACH INLET 3 PULSATOR FRONT CONTROL PANEL ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. WATER DRAIN HOSE SOUND ABSORPTION PANEL For more details, see control panel of your washing machine. Press once again to turn the power off. POWER CONTROL PANEL START/HOLD BUTTON Use to pause and restart the operation. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. INSTALLATION & MAINTENANCE LEVELLING · If the washer is not leveled with the ground, it makes the machine tremble more or be out of order. So, make sure that the washer is leveled properly. SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. · Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. Adjust the side horizontally first and the front in same direction next. If the thread is not within the limit, adjust the height of the legs. · Adjust the legs on feet for levelling . Connect the other end of the water supply hose to the inlet water valve at the back of the washer. 5-1. Connect the other end of the water supply hose to the inlet water valve at the top of the washer. First, using a "+" type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow for gap about 5mm between them. [. . . ] Pull down the part (c) of the water supply hose . When the part (c)is released, c the hose is automatically connected to the adaptor making a 'click' sound. NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. 7 ASSEMBLING THE RAT PROTECTION PANEL Tilt the washer a little and lift up the panel until it clicks, finally fix the panel with screw to the base as shown in the figure. Sisi belakang 1. Insert the sound absorbing panel to the assembling hole on back side to the end. 2. If you have difficulty inserting the panel lift up the washer a little and insert it IN CASE OF PUMP-DRAINED WASHER Take out the cap-hose and connect the outlet-hose. Be sure to join tightly the drain hose into the drain-outlet on the back of the machine. [. . . ]