User manual LG WM-16225FD

[. . . ] In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. 1 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. [. . . ] If any items are missing, contact your dealer. User's Guide/Cards Power Cord DVI-D Signal Cable (Only E1941T/E2041T/WM-16225FD/ E2341T/E2441T ) (This feature is not available in all countries. ) 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it "click". Stand Body Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Base 4. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 5. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture. 4. Use a coin on the back of the Stand Base and turn the screw anticlockwise to loosen. 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator is blinking blue. 11 e 1 2 3 4 / / n s. . . n 2 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) input Main menu Sub-menu BRIGHTNESS ORIGINAL RATIO COLOR TEMP (PRESET/USER) CONTRAST Supported input DSUB DVI-D Description MENU To adjust the brightness of the screen To adjust the image size To customize the color of the screen To adjust the contrast of the screen LANGUAGE FACTORY RESET To customize the screen status for a user's operating environment SUPER ENERGY SAVING ON DSUB DVI-D Turn on the SUPER ENERGY SAVING function. Initialize the SUPER ENERGY SAVING and set to "OFF" mode. OFF RESET NOTE The order of icons may differ depending on the model (13~18). 13 , 14 15 Turn on the SUPER ENERGY SAVING function. Turn off the SUPER ENERGY SAVING function. Now the monitor is LED SAVING function. Clear the TOTAL POWER REDUCTION and TOTAL CO2 REDUCTION values. 17 SAVING DATA(W/h) : 19 inch 20 inch 22 inch 23 inch 24 inch Saving Data depends on the Panel. So, those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal. Set the color setting higher than 24 bits (true color). IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. 20 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. [. . . ] Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. Digital E2441T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1920 x 1080 @60 Hz VESA 1920 x 1080 @60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B (Analog, Digital) On Mode Sleep Mode Off Mode : 25 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 56. 93 cm (22. 41 inch) Height 35. 43 cm (13. 94 inch) Dept 5. 93 cm ( 2. 33 inch) 4. 0 kg (8. 81 lb) < < With Stand Width 56. 93 cm (22. 41 inch) Height 41. 91 cm (16. 50 inch) Depth 17. 93 cm ( 7. 05 inch) Weight(excl. packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 2 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C 5 % to 90 % non-Condensing Humidity Attached ( ), Detached ( O ) Stand Base Power cord Wall-outlet type NOTE Information in this document is subject to change without notice. 29 Specifications Preset Modes (Resolution) E1941T/E1941S *If you can't select 1366 x 768 in display property timing option, please update your video card driver from your video card vendor. (Hz) Polarity(H/V) 1 2 3 4 5 6 7 8 *9 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1366 x 768 31. 468 31. 469 37. 500 37. 879 46. 875 49. 725 48. 363 60. 123 47. 712 70 60 75 60 75 75 60 75 60 -/+ -/-/+/+ +/+ -/-/+/+ +/+ *Recommend Mode E2041T/E2041S Display Modes (Resolution) Horizontal Freq. [. . . ]