User manual LYNX 4VS352IP

[. . . ] 9000 230 334 (8611) Instructions for use en Index 4 6 7 8 9 10 12 14 Washing dishes . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Warning For safety reasons, if the appliance is not fitted in a recess, thereby making a side wall accessible, the door hinge area should be covered at the side. (Risk of injury) Covers are available as optional accessories from customer services or specialist stores. Installation Install and connect the appliance according to the installation and assembly instructions. [. . . ] If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. In order to resume the programme, set the main switch to ON again. Additional functions * * on some models additional functions 4 can be set with the buttons. Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. If you wish to pre-soak the dishes, this programme option must be selected by pressing the "Pre-Soak" button before the programme starts. 5 g poured onto the inside of the door. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. To restart, rotate the programme selector 3 to the required programme. The programme sequence starts automatically. Time reduction/ time saving * Pressing the "Time reduction/time saving" button provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Time reduction/time saving programme option. Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e. g. Note If the power supply is disconnected while the appliance is operating, e. g. by switching off the appliance or due to a power failure, all settings remain stored. Operation continues automatically as soon as the power supply is restored. Half load* If you have only a few items to wash (e. g. The "half load" additional function saves water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Extra dry* If you press the "Extra dry" button, you will receive a higher temperature in all programmes in the final rinse and therefore an improved drying result. (please note that higher temperatures might have an effect on delicate items). 16 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. The filters are permanently attached to each other and cannot be dismantled. Clean the filters under running water. Overall condition of the machine Check washing chamber for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the front of the appliance and panel with a damp cloth; water and a little washing-up liquid will suffice. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Health hazard! Re-installation: Insert the filters and screw the filter cylinder tight. Salt and rinse aid Check the refill indicators 9 8. If required, top up the salt and/or rinse aid. Filters Waste which is deposited on the filters 28 may result in a blockage. 17 en Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 and 24 and the arm mountings . [. . . ] Water pressure: Minimum 0, 05 MPa (0, 5 bar) ­ maximum 1 MPa (10 bar). If you do use hot water, the temperature should not exceed 60 °C. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. Pull out the appliance, carefully pulling the hose behind. Transporting the dishwasher Drain water from the dishwasher. If the appliance is not kept upright during transport, any water left inside may seep into the control module and cause subsequent errors with programme functions. Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor. [. . . ]