User manual LYNX 4VS562BP

[. . . ] 9000 262 069 (8704) Instructions for use en Index 4 6 7 8 9 10 12 13 15 Washing dishes . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Warning For safety reasons, if the appliance is not fitted in a recess, thereby making a side wall accessible, the door hinge area should be covered at the side. (Risk of injury) Covers are available as optional accessories from customer services or specialist stores. Installation Install and connect the appliance according to the installation and assembly instructions. [. . . ] temperature, amount of water, etc. ) The water consumption values refer to a set water hardness value of 4. End of programme The programme has ended when a figure appears in the numerical display 8 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupting the programme Set main switch 1 to OFF. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. In order to continue with the stored programme, set the main switch to ON again. Switching on the appliance Close the door. The expected programme duration is indicated on the numerical display 8 . The programme sequence starts automatically. 16 en Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. To restart, rotate the programme selector 3 to the required programme. The programme sequence starts automatically. Intensive drying By activating the "Intensive drying" function, the final rinse will produce a higher temperature in all programmes resulting in an improved drying result (please note that higher temperatures might have an effect on delicate items). Switch off the main switch 1 ; the chosen setting has now been stored. Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e. g. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. 17 en Additional functions * * on some models additional functions 4 Extra dry* If you press the "Extra dry" button, you will receive a higher temperature in all programmes in the final rinse and therefore an improved drying result. (please note that higher temperatures might have an effect on delicate items). can be set with the buttons. Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. If you wish to pre-soak the dishes, this programme option must be selected by pressing the "Pre-Soak" button before the programme starts. 5 g poured onto the inside of the door. Time delay * h. Time reduction/ time saving * Pressing the "Time reduction/time saving" button provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Time reduction/time saving programme option. Half load* If you have only a few items to wash (e. g. The "half load" additional function saves water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. You can delay the start of the programme in 1-hour steps up to 19 hours. Press the timer programming button until the digital display 8 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. 18 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. [. . . ] If you do use hot water, the temperature should not exceed 60 °C. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. Pull out the appliance, carefully pulling the hose behind. Transporting the dishwasher Drain water from the dishwasher. If the appliance is not kept upright during transport, any water left inside may seep into the control module and cause subsequent errors with programme functions. Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor. The socket must be attached near the dishwasher and be freely accessible. [. . . ]