User manual MATSONIC MS5025

[. . . ] The information presented in this publication has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. Specifications are subject to change without notice. Trademarks IBM, PC/AT, and PC/XT are trademarks of International Business Machines Corporation. Intel and Pentium are trademarks of Intel Corporation. AMD is a trademark of Advanced Micro Devices Inc. Cyrix is a trademark of Cyrix Corporation. IDT is a trademark of Integrated Devices Technology Corporation. AMI is a trademark of American Megatrends Inc. MS-DOS and WINDOWS NT are registered trademarks of Microsoft Corporation. ii Contents Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2: Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Two of which are black, orient the connectors so that the black wires are in the middle. Pin 1 2 3 4 5 6 Description Power Good +5V DC +12V DC 12V DC Ground Ground Pin 7 8 9 10 11 12 Description Ground Ground 5V DC +5V DC +5V DC +5V DC 8 Chapter 2 PWR2 ATX Power Connector The ATX power supply provides a single 20-pin connector and supports the ACPI specification. Pin 1 2 3 4 5 6 7 8 9 10 Description 3. 3V 3. 3V Ground +5V Ground +5V Ground Power OK 5VSB +12V Pin 11 12 13 14 15 16 17 18 19 20 Description 3. 3V 12V Ground PS-ON Ground Ground Ground 5V +5V +5V Software Power-Off Follow the steps below to use the Software Power-Off Control function in Windows 95 with ATX power supply. will not be shown when using this function. Hardware Configuration 9 COM1/2 Serial Port #1/#2 PRN Parallel Port FDC Floppy Disk Port IDE1/IDE2 Primary/Secondary IDE Ports KBD Keyboard Connector J2 ATX FORM CARD Connector: (1-4, 10-13) 2 sets of Universal Serial Bus (USB) Pin 1 2 3 4 Description +5 VDC Data Data + Ground Pin 10 11 12 13 Description +5 VDC Data Data + Ground (5-6, 15-16) PS/2 Mouse Pin 5 6 15 16 Description +5 VDC Mouse CLK Mouse Data Ground (7-9, 17-18) Infrared Pin 7 8 9 17 18 Description Ground IR Hi +5 VDC IR In IR Out 10 Chapter 2 J11 (2, 4, 6, 8, 10) (KEY LOCK) Keylock & Power LED Connector Pin 2 4 6 8 10 Description LED Output N. C. Ground Keylock Ground J11 (1, 3, 5, 7) (SPK) Speaker Connector Pin 1 3 5 7 Description Data Out N. C. Ground +5V J11 (13, 14) (TB-LED) Suspend LED Connector Pin 13 (+) 14 () Description +5V Active Low J11 (15, 16) (HDD-LED) HDD LED Connector Pin + Description +5V Active Low Hardware Configuration 11 J11 (17, 18) (RST) Reset Switch Connector Setting Open Close Description Normal Mode Reset System J5 (CPU-FAN) Fan Power Connector Pin 1 2 3 Description N. C. +12V Ground JP6 (PWR-BT) Over Ride Power Button Connector Attach the ATX Power Button or Suspend Switch cable to this connector. In the AT power system, this connector will act as a suspend switch; and in the ATX power system, this connector will be not only an ATX power button but a suspend switch as well. Details are described below: When the system is off, push the power button to turn the system on. When the system is on, push the power button rapidly to switch the system to the Suspend mode, and, by pushing and holding the button for more than 4 seconds to turn the system completely off. When the system is in the Suspend mode, push the power button rapidly to turn the system on. 12 Chapter 2 JP1 (WOL) Wake On LAN Connector While in Soft-off/Suspend state, if an external LAN signal occurs, the system wakes up and can be accessed with the LAN card. Pin 1 2 3 Description 5V Stand By Ground Active Low Jumper Settings J1 CMOS RAM Discharge Selector Setting Normal Mode Clear CMOS Description 1 1 JP2 DIMM Voltage Selectors Voltage 5V 3. 3V Settings 1 3 1 3 Hardware Configuration 13 Memory Installation The mainboard lets you add up to 256MB of system memory through SIMM and DIMM sockets on the board. Four SIMM sockets on the mainboard are divided into two banks: Bank 1 and Bank 2. When Hit <DEL> if you want to run SETUP appears, press the <DEL> key to enter the BIOS setup program. The following screen appears: AMIBIOS Setup, Version - 2. 4 (C) 1997, American Megatrends Inc. Security 2. American Megatrends Setup Standard Advanced Chipset User CPU Anti-Virus PCI Power Mgmt PCI/PnP Peripheral Utility CPU PnP Default Detect IDE Original Optimal Best Set Date, Time, Floppy, Hard Disk Alt+H: Help 3. Use your keyboard or mouse to choose options. Press Alt-H for Help. 16 Chapter 3 Default Every option in BIOS Setup contains three default values: Original default, Best default, and the Optimal default value. Original: The original default values recover the modified settings to the original values. Optimal: The Optimal default values provide optimum system settings for all devices and system features. Best: The Best default values provide best performance settings for all devices and system features, but dependent used devices and we arent guaranty that system run overnight on these settings. Setup Window The Setup section has six icons that allow you to set system configuration options. Setup Standard Advanced Chipset PCI Power Mgmt PCI/PnP Peripheral BIOS Setup 17 Standard Setup Choose the Standard icon from the Setup section on the BIOS Setup main menu. Pri Master Pri Slave Sec Master Sec Slave Choose these icons to configure the hard disk drive named in the option. When you click on an icon, the following parameters are listed: Type, LBA/Large Mode, Block Mode, 32Bit Mode, and PIO Mode. [. . . ] The system enters the full power on state if any activity occurs. RTC Alarm Set this option to enable the RTC Alarm to Resume From Soft wake up the system which is Soft Off. Off RTC Alarm Date; Set these options to specify the RTC Alarm RTC Alarm Hour; time on Date/Hour/Minute/Second. RTC Alarm Minute; RTC Alarm Second BIOS Setup 23 PCI/PnP Setup Choose the PCI/PnP icon from the Setup section on the BIOS Setup main menu. Plug and Play Aware OS Set this option to Yes if the operation system in this computer is aware of and follows the Plug and Play specification. [. . . ]