User manual MATSONIC MS6393E

[. . . ] MS6393E Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, and PS/2 are registered trademarks of International Business Machines. [. . . ] IDE Devices IDE devices include hard disk drives, high-density diskette drives, and CD-ROM or DVD-ROM drives, among others. The mainboard ships with an IDE cable that can support one or two IDE devices. If you connect two devices to a single cable, you must configure one of the drives as Master and one of the drives as Slave. The documentation of the IDE device will tell you how to configure the device as a Master or Slave device. Use the cable provided to connect the device(s) to the Primary IDE channel connector IDE1 on the mainboard. If you want to install more IDE devices, you can purchase a second IDE cable and connect one or two devices to the Secondary IDE channel connector IDE on the mainboard. If you have two devices on the cable, one must be Master and one must be Slave. 17 MS6393E Mainboard User's Manual Internal Sound Connections If you have installed a CD-ROM drive or DVD-ROM drive, you can connect the drive audio cable to the onboard sound system. There are two kinds of connector because different brands of CDROM drive have different kinds of audio cable connectors. Connect the cable to the appropriate connector. CD2 1 CD1 Infrared Port You can connect an infrared port to the mainboard. You can purchase this option from third-party vendors. IR 1 2 3 4 5 VCC IRRX IRTX GND 1. If you are adding an infrared port, connect the ribbon cable from the port to the IR header and then secure the port to an appropriate place in your system chassis. 18 Expansion Slots This mainboard has two 32-bit PCI expansion slots and one ADIMM slot. The PCI slot PCI1 is shared with the ADIMM slot, the PCI slot PCI2 is shared with the USB port. It means that you can use either one of shared both but you cannot use the both at the same time. PCI2 PCI1 ADIMM Follow the steps below to install a PCI expansion card. Insert the expansion card edge connector into the slot and press it firmly down into it so that it is fully inserted. Secure the expansion card bracket to the system chassis using the screw that held the slot cover in place. You can purchase an optional SiS301 video bridge card which supports an NTSC/PAL video encoder with a Macrovision V7. 1. L1 option for TV display, a TMDS® transmitter with bi-linear scaling capability for a TFT LCD panel display, or an analog RGB port to support a secondary CRT monitor display. The second display can display independent resolutions, color depths and frame rates different from the primary VGA display. The card receives digital video signals and control 19 MS6393E Mainboard User's Manual signals from the VGA circuitry and transforms them into composite or component video output for a TV display, TMDS® signals for an LCD display or analog RGB signals for a secondary CRT display. 20 Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information about your computer such as the date and time, the kind of hardware installed, and various configuration settings. Your computer uses this information to initialize all the components when booting up and functions as the basis for coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. If this happens, you can use the clear CMOS jumper to clear the CMOS memory used to store the configuration information, or you can hold down the Page Up key while you reboot your computer. [. . . ] All Rights Reserved --- Hardware Monitor --CPU Temperature System Temperature CPU Fan Speed Chassis Fan Speed Vcore +1. 800V Vcc3 Vcc +12V SB5V 30°C/86°F 2. 000 V 1. 800 V 3. 300 V 5. 000 V 12. 000 V 5. 000 V ESC F1 F5 F6 F7 : : : : : Quit : Select Item Help PU/PD/+/- : Modify Old Values (Shift)F2 : Color Load Optimal values Load Best performance values CPU / System Temperature FAN Speeds & Voltage Measurements These items display CPU/system temperature measurement. These items indicate cooling fan speeds in RPM and the various system voltage measurements. 33 MS6393E Mainboard User's Manual Change Password If you highlight this item and press Enter, a dialog box appears which lets you enter a Supervisor password. The password is then required to access the Setup Utility or for that and at start-up, depending on the setting of the Password Check item in Advanced Setup. Change or Remove the Password Highlight this item, press Enter and type in the current password. [. . . ]