User manual MATSONIC MS7012D

[. . . ] Important Information Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] For some add-in cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-in card. PCI add-in card PCI slot Metal bracket Edge connector Note: If you have installed an AMR card, you should check the settings of jumpers JP3 (audio/modem enable/disable) and JP6 (select onboard codec or AMR codec). You should disable the onboard audio/modem to avoid conflicts with the AMR card. You can use the AMR codec chip (if it has one) or the onboard codec chip. 35 Add-in Card Options The mainboard has two features that can be used if you have installed either a fax/modem card or a network adapter card. WOL1: Wake on LAN If you have installed a network adapter (LAN adapter), you can use the cable provided with the card to plug into the WOL1 connector on the mainboard. When your system is in a power­saving mode, any traffic through the network automatically resume the system. You must enable this item using the Power Management page of the setup utility. See Chapter three for more information. WOL1 WOM1 WOM1: Wake on Modem If you have installed a fax/modem card, you can use the cable provided with the card to plug into the WOM1 connector on the mainboard. When your system is in a power­saving mode, any incoming calls to the modem automatically resume the system. You must enable this item using the Power Management page of the setup utility. See Chapter Three for more information. 36 Install Options and Extension Brackets This mainboard has a number of special connectors that allow you to add optional features to your system. You can install any of the following items: Fax/modem card option Infrared port Serial port extension bracket 24-bit digital audio extension bracket (SPDIF) TV-out extension bracket Fax/modem Card You must install the fax/modem card in order to use the built-in fax/modem. J8 The fax/modem card is supplied with this mainboard. Remove the expansion slot blanking plate from the system chassis that is adjacent to the fax/modem connector. The RJ11 Line and Telephone sockets on the bracket are positioned in the expansion slot with the removed blanking plate. 37 Line and Tel RJ11 sockets Fax/modem card J8 fax/modem connector Serial Port Extension Bracket If you want to have a second external serial port available in your computer case, you must install a serial port extension bracket. COM2 1. Remove a blanking plate from a free expansion slot in the system chassis. Plug the cable from the serial port extension bracket into the COM2 connector on the mainboard. The port connected to COM2 is identified as COM2/4 Install the metal bracket into the expansion slot in the system chassis from which you removed the blanking plate. Secure the bracket by driving a screw through the slot in the top of the metal bracket into the system chassis. 38 Note: An IR port and a second serial port use the same resources, and they may use some of the resources required by a fax/modem card. If you have more than one of these items installed, you may not be able to use them at the same time. You can use the Peripherals page of the setup utility to switch resources between an IR port and a second serial port. TV-out Extension Bracket The TV-out extension bracket provides video out jacks (RCA and/or Svideo). You can use these jacks to connect your computer to a TV set or digital flat panel display. TV1 1. Remove a blanking plate from a free expansion slot in the system chassis. [. . . ] The directX drivers need to be installed before you install an AGP driver. You may be able to get more up-to-date directX drivers from the Microsoft web site. Start the installation by clicking on the file DX5CORE. EXE. 66 PC-Cillin Anti-Virus Utility Anti-virus software is provided for DOS, for WIN95, and WIN 98. For DOS, copy all the files in the DOS folder to your hard disk drive. [. . . ]