User manual MATSONIC MS7023D

[. . . ] Important Information Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] In the system case, remove the blanking plate from the slot in the system case that corresponds to the expansion slot that you are going to use. Position the edge connector of the add-in card over the expansion slot. Position the metal bracket of the card in the empty slot in the system case. Install the edge connector of the add-in card into the expansion slot. Press down quite firmly so that you are sure that the edge connector is correctly seated in the slot. 34 6. 7. Secure the metal bracket of the card in the empty slot in the system case with a screw. For some add-in cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-in card. PCI add-in card PCI slot Metal bracket Edge connector Note: If you have installed an AMR card, you should check the settings of jumpers JP4 (audio/modem enable/disable) and JP6 (select onboard codec or AMR codec). You should disable the onboard audio/modem to avoid conflicts with the AMR card. You can use the AMR codec chip (if it has one) or the onboard codec chip. 35 Add-in Card Options The mainboard has two features that can be used if you have installed either a fax/modem card or a network adapter card. WOL1: Wake on LAN If you have installed a network adapter (LAN adapter), you can use the cable provided with the card to plug into the WOL1 connector on the mainboard. When your system is in a power­saving mode, any traffic through the network automatically resume the system. You must enable this item using the Power Management page of the setup utility. See Chapter three for more information. WOL1 WOM1 WOM1: Wake on Modem If you have installed a fax/modem card, you can use the cable provided with the card to plug into the WOM1 connector on the mainboard. When your system is in a power­saving mode, any incoming calls to the modem automatically resume the system. You must enable this item using the Power Management page of the setup utility. See Chapter three for more information. 36 Install Options and Extension Brackets This mainboard has a number of special connectors that allow you to add optional features to your system. You can install any of the following items: Fax/modem card option Network adapter extension bracket Infrared port 24-bit digital audio extension bracket (SPDIF) Fax/modem Card You must install the fax/modem card in order to use the built-in fax/modem. J4 37 The fax/modem card is an optional item supplied with this mainboard. Remove the expansion slot blanking plate from the system chassis that is adjacent to the fax/modem connector. The RJ11 Line and Telephone sockets on the bracket are positioned in the expansion slot with the removed blanking plate. Line and Tel RJ11 sockets Fax/modem card J4 fax/modem connector 38 Infrared Port This option can be purchased from third-party vendors. SIR1 1. 2. If you are installing an optional serial infrared port, connect the cable from the optional IR port to the SIR1 connector on the mainboard. After you have connected the cable, secure the optional IR port to the appropriate place on your system case. Note: An IR port may use some of the resources required by a fax/modem card. [. . . ] You may be able to get more up-to-date directX drivers from the Microsoft web site. Start the installation by clicking on the file DX5CORE. EXE. 65 PC-Cillin Anti-Virus Utility Anti-virus software is provided for DOS, for WIN95, and WIN 98. For DOS, copy all the files in the DOS folder to your hard disk drive. For Windows 98, run SETUP. CMI8X38 Folder Installation Notes Audio Software This folder has software and drivers for the sound system that is integrated on this mainboard. [. . . ]