User manual MATSONIC MS7047D

[. . . ] Main Board User's Manual able Table of Contents Chapter 1-1 1-2 1-3 Chapter 2-1 2-2 2-3 2-4 2-5 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Soft-OFF by PWR-BTTN function in BIOS's Power Management Setup menu must be set to "Delay 4 Sec. " to activate this function. When the Soft-OFF by PWR-BTTN function is enabled, pushing the power button rapidly will switch the system to Suspend mode. Any occurrence of external activities such as pressing a key on the keyboard or moving the mouse will bring the system back to Full-On. Pushing the button while in Full-On mode for more than 4 seconds will switch the system completely off. Power Indicator LED Connector The power indicator LED shows the system's power status. It is important to pay attention to the correct cables and pin orientation (i. e. , not to reverse the order of these two connectors. ) Over-ride Power Button Operation Pin 1 Power Indicator LED Definition +5V DC No Connection Ground 2 3 Software Power-Off Control This mainboard can be powered down using the Windows 95/98 Software Power-Off function. To power down your computer, click the START button on the Windows 95/98 task bar. The message "It is now safe to turn off your computer" will not be shown when using this function. 13 Chapter 2 C. Green Switch/Green LED Connector Some ATX cases provide a Green switch which is used to put the system in Suspend mode. In Suspend mode, the power supply to the system is reduced to a trickle, the CPU clock is stopped, and the CPU core is in it's minimum power state. The system resumes in different ways as defined by Power Management Setup screen in BIOS. System Reset Switch Connector This connector should be connected to the reset switch on the front panel of the system case. The reset switch allows you to restart the system without turning the power off. Pin 1 2 Definition System GND E. Speaker Connector Pin 1 2 3 4 Definition Speaker Signal No Connection No Connection +5V DC F. IDE Activity LED Connector The IDE activity LED lights up whenever the system reads/writes to the IDE devices. Turbo LED Connector This mainboard does not have a Turbo/De-turbo speed modes. So the turbo LED will always light. Blinking LED in Suspend Mode While in Suspend mode, the LED light on the front panel of your computer will flash. Suspend mode is entered by pressing the Override Power Button, pushing the Green button on your ATX case, or enabling the Power Management and Suspend Mode options in BIOS's Power Management menu. 14 Hardware Setup PS/2 Keyboard Power On Function (JP1) 1 Disabled 1 Enabled This board is able to be turned on by the keyboard. To use this function, enable the Power On Function option in BIOS's Integrated Peripherals screen (See section 3-8). You must also set this jumper's cap to pins 2-3 to use this function. Some outof-date keyboards may require larger current than supplied by the Suspend 5V of modern power supplies. When using older keyboards disable this function. Audio Line_out or Speaker_out (JP2/JP3) JP2 1 JP2 1 JP3 JP3 Speaker_ out Line_out (default) This jumper allows you to select between audio line-out or speaker out function. [. . . ] The primary screen as shown in Figure 3-1 is a list of the menus and functions available in the setup program. Operating commands are located at the bottom of this and all other BIOS screens. When a field is highlighted, on-line help information is displayed on the right side of the screen. CMOS Setup Utility- Copyright (C) 1984-2000 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc F10 : Quit : Save & Exit Setup Time, Date, Hard Disk Type. . . SeePU Setup Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item Figure 3-1 Setup Program Initial Screen 23 User's Manual Memo 24 Chapter 4 Brief Software Driver Guide The Mainboard Software Guide is found on the CD-ROM that is enclosed with your mainboard and is a PDF file which must be viewed with Adobe's freeware called Acrobat® Reader. [. . . ]