User manual MATSONIC MS7167D

[. . . ] Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, and PS/2 are registered trademarks of International Business Machines. [. . . ] When enabled, the graphics card's local memory will be cached for faster execution. However, if any program writes to this memory area, a system error may result. This option determines the frame buffer size shared from the main memory for use by the onboard VGA display. This option determines the effective size of the AGP Graphic Aperture, where memory-mapped graphic data structures are located. This item allows you to enable or disable the caching of display data for the video memory of the processor. If your graphics display card does not support this feature, you need to disable this item. This item can be used to signal driving current on AGP cards to auto or Manual. Some AGP cards need stronger than normal driving current in order to operate. When the previous item AGP Driving Control is set to Manual, you can use this item to set the AGP current driving value. This item allows you to enable the USB port, if you have installed a USB device on the system board. This should be enabled if your system has a modem installed on the system board and you wish to use it. When enabled, up to four words of data can be written to the PCI bus without interrupting the CPU. When disabled, a write buffer is not used and the CPU read cycle will not be completed until the PCI bus signals that it is ready to receive the AGP Driving Control AGP Driving Value OnChip USB USB Keyboard Support OnChip Sound OnChip Modem CPU to PCI Write Buffer 22 3: BIOS Setup Utility data. PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction PCI#2 Access #1 Retry AGP Master 1 WS Write AGP Master 1 WS Read When enabled, every write transaction goes to the write buffer. "Burstable" transactions then burst on the PCI bus and "nonburstable" transactions do not. When enabled, writes to the PCI bus are executed with zero wait states. The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. When enabled, the AGP Bus (PCI#1) access to PCI Bus (PCI#2) is executed with the error retry feature. By default, two-wait states are used by the system, allowing for greater stability. By default, two-wait states are used by the system, allowing for greater stability. 23 MS7167 Mainboard User's Manual Integrated Peripherals Page This page sets some of the parameters for peripheral devices connected to the system. CMOS Setup Utility ­ Copyright (C) 1984 ­ 2000 Award Software Integrated Peripherals On-Chip IDE Channel0 On-Chip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA Init Display First Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART 2 Mode x IR Function Duplex x TX, RX inverting enable Onboard Parallel Port Enter : Select : Move F1:General Help Defaults F7:Optimized Defaults Enabled Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto PCI Slot Enabled 3F8/IRQ4 2F8/IRQ3 Standard Half No, Yes 378/IRQ7 +/-/PU/PD:Value: F10: Save F5:Previous Values Item Help Menu Level ESC: Exit F6:Fail-Safe On-Chip IDE Channel 0, 1 Primary/Secondar y Master/Slave PIO Use these items to enable or disable the PCI IDE channels that are integrated on the mainboard. These four items let you assign which kind of PIO (Programmed Input/Output) is used by IDE devices. You can choose Auto, to let the system auto detect which PIO mode is best, or you can install a PIO mode from 0-4. This motherboard supports UltraDMA and provides faster access to IDE devices. [. . . ] Click Start\Select Settings\Select Control Panel, Doubleclick Add/Remove Programs. Click the OK button and Windows will automatically uninstall GAMUT2000. When finished uninstalling, click the OK button. First Installation Step 1. You may also start the installation process by clicking Start\Selecting Run\Clicking Browse and finding the Setup. exe file in the GAMUT2000 CD. [. . . ]