User manual MATSONIC MS7191SM

[. . . ] This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, OS/2, and PS/2 are registered trademarks of International Business Machines. [. . . ] Connect the case switches and indicator LEDs to the bank of switch and LED connectors J10. See the illustration below for a guide to the pin functions of the J10 case connector. 12 Speaker Pins 1-3-5-7 Power LED Pins 2-4-6 Keylock Pins 8-10 Turbo LED Pins 13-14 HDD LED Pins 15-16 Reset Switch Pins 17-18 Suspend LED Pins 19-20 Power/Suspend Switch Pins 21-22 21 22 Install the Extension Brackets The extension brackets are used to transmit features on the mainboard to external connectors that can be fixed to the system chassis. Note: All the ribbon cables used on the extension brackets carry a red stripe on the pin-1 side of the cable. Audio Ports and Game/MIDI Port Extension Bracket This bracket provides three audio jacks for stereo line in, stereo line out and microphone. In addition it has a 15-pin D-connector which can be used by either a joystick or a MIDI device. If you are using a four channel speaker system, channel one and two are output through the Stereo Line-out, and the rear speaker channels three and four are output through Stereo Line-in. On the mainboard, locate the J4 audio header for this bracket. 16 ! J4-Audio Header 1 Stereo Line-in /Rear speaker channels 3-4 Microphone Stereo Line-out /Speaker channels 1-2 Game/MIDI Audio Ports & Game/MIDI Extension Bracket 2. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. Serial Ports Extension Bracket This bracket has two serial ports; COM1 (9-pins) and COM2 (25pins). On the mainboard, locate the two headers COM1 and COM2 for this bracket. Plug the two cables from the bracket into the appropriate COM1 and COM2 headers. 17 ! 1 1 COM1 Header COM2 Header Serial Port COM1 Serial Port COM2 Serial Ports Extension Bracket 3. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. Parallel Port Extension Bracket This bracket has one parallel port LPT1. PRN1 1 Parallel port LPT1 Parallel Port Extension Bracket 1. On the mainboard, locate the parallel port headers PRN1 for this bracket. 18 !In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. Fax/Modem DAA Module The Fax/Modem DAA module plugs directly into the mainboard adjacent to an expansion slot in the system chassis. When you remove the blanking plate from the system chassis, you can access the LINE and TEL RJ11 phone jacks on the metal edge of the Fax/Modem DAA module. J3-MODEM Header GND 1 GND 3 GND 5 AUX 3V 7 HOOK 9 RIN 11 AUX 5V 13 MUTE 15 2 MCLK 4 FRA-SY 6 SCLK 8 RIN-WAK 10 GPIO 12 SDO 14 SDI 16 RST 1. [. . . ] If you are using a very old drive that can't be detected, you can install it manually. Setup will check for two devices on the primary IDE channel and then two devices on the secondary IDE channel. Press Y, then Enter to tell the system to auto-detect the device. Save Settings and Exit Highlight this item and press Enter to save the changes that you have made in the setup utility and exit the setup program. the Save and Exit dialog box appears, press Y to save and exit, or press N to return to the setup main menu. Exit Without Saving Option Highlight this item and press Enter to discard any changes that you have made in the setup utility and exit the setup program. [. . . ]