User manual MATSONIC MS8157E VERSION 1.0

[. . . ] Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademarks IBM, VGA, and PS/2 are registered trademarks of International Business Machines. [. . . ] Internal Sound Connections If you have installed a CD-ROM drive or DVD-ROM drive, you can connect the drive audio cable to the onboard sound system. 1 J1 1 1 SIR1 1 CD2 CD1 On the mainboard, locate the two 4-pin connectors CD1 and CD2. There are two kinds of connector because different brands of CD ROM drive have different kinds of audio cable connectors. CD1 Pin 1 2 3 4 Signal GND CD IN L GND CD IN R CD2 Pin 1 2 3 4 Signal CD IN L GND GND CD IN R 20 2: Mainboard Installation Infrared Port You can connect an infrared port to the mainboard. You can purchase this option from third-party vendors. Pin 1 3 5 Signal NC +5V IRTX Pin 2 4 6 Signal KEY GND IRRX 1. If you are adding an infrared port, connect the ribbon cable from the port to the SIR1 header and then secure the port to an appropriate place in your system chassis. Onboard LAN LED Connections If you have a set indicator LEDs for the onboard LAN communication, you can connect the LED cable to the header J1. Pins 3-4 are for 10/100 Mbps mode LED, the onboard LAN run in 100 Mbps mode when the LED lit. Pin 1 3 Signal Link LED LED+ Pin 2 4 Signal LED+ 10/100 Mbps mode LED 21 Mainboard User's Manual Expansion Slots This mainboard has one AGP, one CNR and five 32-bit PCI slots. PCI5 PCI3 PCI1 CNR1 PCI4 PCI2 AGP1 Follow the steps below to install a PCI/AGP/CNR expansion card. Secure the metal bracket of the card to the system chassis with a screw. 22 2: Mainboard Installation Wake On LAN (WOL) If you have installed a LAN adapter expansion card, connect the card to the Wake On LAN connector WOL1. This allows incoming traffic to resume the system from a software power down. You need to enable this feature in the BIOS setup utility. WOL1 Header Pin 1 2 3 Signal 5VSB GND RIJ 23 Mainboard User's Manual 24 3: BIOS Setup Utility Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information of your computer, such as date and time, the type of hardware installed, and various configuration settings. Your computer applies the information to initialize all the components when booting up and basic functions of coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. If it happens, you can use the clear CMOS jumper to clear the CMOS memory which has stored the configuration information; or you can hold down the Page Up key while rebooting your computer. You might need to do this to configure some hardware installed in or connected to the mainboard, such as the CPU, system memory, disk drives, etc. 25 Mainboard User's Manual Running the Setup Utility Every time you start your computer, a message appears on the screen before the operating system loading that prompts you to "Hit <DEL>if you want to run SETUP". Whenever you see this message, press the Delete key, and the Main menu page of the Setup Utility appears on your monitor. AMIBIOS SIMPLE SETUP UTILITY ­ VERSION 1. 21. 12 (C) 2000 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced Setup Power Management Setup PCI / Plug and Play Setup Load Optimal Settings Load Best Performance Settings Features Setup CPU PnP Setup Hardware Monitor Change Password Exit Esc : Quit : Select Item (Shift)F2 : Change Color F5 : Old Values F6 : Optimal values F7 : Best performance values F10 : Save&Exit Standards COMOS setup for changing time, date, hard disk type, etc. You can use the cursor arrow keys to highlight any of the options on the main menu page. To cycle through the Setup Utility's optional color schemes hold down the Shift key and press F2. Some of the options on the main menu page lead to tables of items with installed values. In these pages, use the cursor arrow keys to highlight the items, and then use the PgUp and PgDn keys to cycle through the alternate values for each of the items. Other options on the main menu page lead to dialog boxes requiring you to answer Yes or No by hitting the Y or N keys. If you have already made changes to the setup utility, press F10 to save those changes and exit the utility. Press F7 to install the setup utility with a set of high-performance values. 26 3: BIOS Setup Utility Standard CMOS Setup Page Use this page to set basic information such as the date, the time, the IDE devices, and the diskette drives. [. . . ] This item assigns either IRQ 5 or 7 to the parallel port. Parallel Port IRQ 34 3: BIOS Setup Utility Parallel Port DMA OnBoard Game Port OnBoard MIDI Port/IRQ MIDI Port IRQ OnBoard IDE Ethernet Device Audio Device Modem Device USB Controller USB Device Legacy Support ThumbDrive Support for DOS This item assigns a DMA channel to the parallel port. This item enables or disables the onboard MIDI port, and assigns a port address. This item enables or disables either or both of the onboard Primary and Secondary IDE channels. This item enables the USB device, if you have installed a USB device on the system board. [. . . ]