User manual MCINTOSH MHT200

[. . . ] A/V System Controller MHT200 Owner's Manual Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. [. . . ] Calibrating: Left Speaker dist. : 2. 5ms complete: 1/3 Press MENU to abort autocalibration Loudspeaker Manual Time Delay Location Default Setting New Setting Left Front Center Right Front Right Surround Right Back Left Back Left Surround Subwoofer 10 10 10 10 none 10 10 10 Figure 24 Automatic Time Delay Calibration 1. Remove the McIntosh Calibration Microphone, battery, hook-up cable and microphone stand adapter from the shipping carton. Note: If the Automatic Speaker Level was previously performed using the supplied microphone, proceed to step 4. 2. This can be accomplished by rotating the large 32 SETUP, con't How to Adjust the Subwoofer Settings cylindrical microphone body below the Power On/Off counterclockwise. Make sure the battery is installed into the microphone, with the battery polarity matching the diagram located inside the battery compartment. Note: If the microphone is not going to be used for a long period of time, remove the battery. 3. Attach the hookup cable with connectors to the microphone, making sure the cable end with the locking collar attches to the microphone, and place the microphone into the stand adapter, with the stand adapter attached to a suitable microphone stand. Switch the Power On to the Microphone by moving the slide switch towards the color dot. Press and hold the Front Panel SETUP Push-button for approximately three seconds. The word SETUP will appear on the Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/ TV screen. Using the Up or Down directional push-buttons select Speaker Setup on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. Refer to figure 21 on page 31. Note: It is extremely important to have the room as quiet as possible where the testing is occurring (temporally switch off TVs, heating/cooling equipment and radios, etc. ) as this will yield the most accurate results. The Subwooofer Settings allow for optimizing performance in the Home Theater System that relate to Room Acoustics and Loudspeaker Characteristics. For most Systems the default setting will produce the best performance. Refer to the Owner's Manual that came with the Loudspeaker, your Dealer and/or the manufacturer of the Loudspeaker for recommendations. A chart on page 35 has been provided to record the Subwoofer Settings. Note: Before adjusting the SUBWOOFER SETTINGS, you FIRST must have performed the SPEAKER SIZE, SPEAKER TIME DELAY and SPEAKER LEVEL Adjustments. 1. Press and hold the Front Panel SETUP Push-button approximately three seconds to enter the Setup Mode. The word SETUP will appear on the MHT200 Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/TV screen. Using the Up or Down directional push-buttons select Subwoofer Settings on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. Note: The first time the SUBWOOFER SETTINGS is accessed, the default settings will be indicated. 6. Using the Up or Down directional push-buttons select AUTOCALIBRATE DELAYS on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. The Automatic Calibration Mode of the MHT200 will go through many tests for each of the active Loudspeaker Channels. The On-Screen Display will provide a status update of the testing as it progresses. If you do not wish to perform SUBWOOFER SETTINGS adjustments at this time, proceed to the next step. The MAIN SETUP Menu will reappear on the Monitor/TV screen and select EXIT from the Menu. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. [. . . ] LABEL FM1 Auto 91. 50 MHz KABC EXIT Figure 82 MENU: TUNER PRESETS 1. PRESET ASSIGNED FM1 Auto 91. 50 MHz KABC Yes EXIT Figure 83 63 How to Operate the Tuner How to Operate the Tuner The McIntosh MHT200 TM1 AM/FM Tuner Module incorporates an advanced design AM/FM Tuner with many desirable performance features to enhance your enjoyment of radio broadcasts. There are several methods of tuning to an AM/FM Broadcast Station by using the Front Panel Trim/Tune Function and the Remote Control. Rotate the TRIM SELECT Control to the TUNE Position and press the TRIM/TUNE Up or Down Push-button on the Front Panel until the desired AM or FM Broadcast Station Preset is selected. [. . . ]