User manual MERLIN QUICKBUILD

[. . . ] QuickBUILD QuickMAP Creation Software Users Manual TABLE OF CONTENTS SECTION 1 ­ INTRODUCTION An Overview of the ISP-100 Hardware Introduction to the ISP-100 MAPTool Software SECTION 2 ­ INSTALLATION Computer Requirements for running MAPTool Installing MAPTool on Your Computer SECTION 3 ­ ISP-100 DSP ARCHITECTURE ISP-100 Input/Output Capabilities DSP "Processing Engine" I/O Interconnect SECTION 4 ­ BUILDING A QuickMAP The Device Menu Monitoring DSP Resource Meters Selecting and Placing Inputs (Gain) Selecting and Placing Outputs (Dither) Selecting and Placing Processing Devices Editing Device Parameters 1. Renaming Devices Moving Devices Deleting Devices Wiring Devices Choosing a Line Style Wiring the Selector (Router) Device Wiring the Combiner (Mixer) Device Meter Dialog Window Naming Outputs DSP Resource Errors Wiring Errors Delay Compensation Saving and Opening . qms Files 2 SECTION 5 ­ Documenting Your System Defining System Description Printing System Block Diagram Printing System Resources and Device Usage SECTION 6 ­ Advanced Design (Under Construction) 3 SECTION 1 ­ INTRODUCTION ___________________________________ An Overview of the ISP-100 The ISP-100 is the first in a line of high quality signal processing products from Telex Communication's Merlin division. Merlin represents a continued commitment to understanding and meeting our customers needs through the development of innovative and intuitive solutions. The ISP-100 is designed with flexibility in mind, providing a powerful tool that allows you to adapt to ever-changing markets and applications. [. . . ] Editing Crossover Parameters The Crossover devices in QuickBUILD will allow you to create filter devices after each output of that given crossover. After selecting and placing the desired crossover, right click and select "Edit". For this example, we will look at a four-way crossover dialog window: Figure 15. If you desire to have a Filter Tool after any or all of the crossover outputs, you can select the number of bands for those devices here. You can also select which DSP chip these filters reside in, but there are some rules: a) If you place your crossover in DSP #1, the filters can be placed in either DSP 1, DSP 2, or DSP 3. b) If you place your crossover in DSP # 2, the filters can only be placed in DSP 2 or DSP 3. c) If you place your crossover in DSP #3, the filters can only reside in DSP 3. This feature can prove beneficial when you are trying to "shuffle" around DSP resources. The same rule applies regarding Y memory placement as mentioned in Editing Filter Tool Parameters. 17 After you have selected the desired number of filters, click the "OK" button. You will then see a series dialog windows relating to each crossover output. You will see one of these dialog windows for every output of the chosen crossover, if additional filters for that output have been selected. (If no additional filters have been selected for any or all of the Crossover outputs, you will be prompted for Crossover output designation when you wire the device. ) This allows you to rename that particular filter device. After you click "OK", you will then be prompted to place the device where you want it on the screen. Figure 17. When you have finished, your crossover device (in this case a 4-way) should look something like this (Your wire lines may look different. You can select different line styles later): Figure 18. 18 3. Editing Delay Parameters Delay times are generated in the ISP-100 by using system memory and NOT DSP cycles. This is a great advantage over some other products by not wasting DSP resources for this function. Therefore, when you change delay parameters, you will not see any impact on DSP resources. Each DSP chip is capable of a maximum of 2. 7 seconds (2700 Ms), for a total system allocation of 8. 1 seconds (8100 Ms). The QuickBUILD software will monitor your delay usage per chip and not allow you to exceed this limit. For example, if you place a 2500 Ms delay in a given chip, the next delay device you place (in that same chip) will only be allowed up to 200 Ms. If you did not assign a delay time when you placed your Delay device, or you want to change that time, right mouse click and select "Edit". [. . . ] If you think that your file may at some point be running on one of these systems, you may want to limit your file name for easier clarification. If you know that it will only be running on Windows 95 or higher, you may use a longer file name. QuickBUILD files default to being stored in the "C:\Programs\Maptool" directory. To open these files in your VUE-IT software, they will need to be moved to the correct sub-directory in VUE-IT. [. . . ]