User manual METABO STE 90 SCS

[. . . ] General Safety Instructions For your own protection and for the protection of your electrical tool, pay attention to all parts of the text that are marked with this symbol!WARNING – Reading the operating instructions will reduce the risk of injury. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury. Special Safety Instructions Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. [. . . ] 1 Clamping lever for securing the saw blade 2 Saw blade clamping fixture 3 Saw blade support roller 4 Saw blade 5 Metal guide of the guide element 6 Guide element 7 Unlocking key for removal of the guide element 8 Anti-splintering footplate insert 9 Footplate 10 LED lights 11 Protective cap 12 Protective rod for preventing unintentional contact with the saw blade 13 Adjustment lever for pendulum motion 14 Switch button on the chip blower 9 en ENGLISH 15 16 17 18 19 20 Sliding switch Hexagon spanner Setting wheel for speed adjustment Extractor connection piece Screw for adjusting the footplate Curved support plate indicating preset cutting angle * depending on equipment/not in scope of delivery Inserting the saw blade Danger of injury due to the sharp jigsaw blade. Ensure that the saw teeth are facing forwards and the blade is seated correctly in the groove on the saw blade support roller (3). 4 Attaching / Removing the protective cap Attachment: Push on the protective cap (11) from the front until it engages Removal: Grip both sides of the protective cap (11), lift slightly, then pull forwards and remove. 5 Sawing with dust extraction - Connect a suitable extraction device to the extractor connection piece (18). 6 Sawing without dust extraction - Work with the protective cap (11) removed (see Removal chapter 6. - Then slide the footplate (9) forwards or backwards and engage in one of the detents (the detents can be viewed through the semicircular opening at the rear of the footplate (9). ) The preset angle is indicated on the curved support plate (20) on the footplate. 8 Sawing close to the wall Remove the protective cap (11), anti-splintering footplate insert (8), circular-cutting and parallel guide. - Slacken the screw (19) until the footplate (9) can be raised slightly. - Raise the footplate (9) slightly and slide backwards up to the stop. Commissioning Before plugging in, check to see that the rated mains voltage and mains frequency, as stated on the rating label, match your power supply. Tips and Tricks Plunging The jigsaw blade can plunge into workpieces made from thin, soft materials without the necessity of drilling a hole beforehand. Position the jigsaw with the front edge of the footplate (9) on the workpiece. Once the saw blade has penetrated the workpiece, the pendulum motion can be activated. In thicker workpieces, a hole for inserting the saw blade must be drilled first. Use only accessories which fulfil the requirements and specifications listed in these operating instructions. A Circular-cutting and parallel guide For the complete range of accessories, see www. I) Place the clamping elements (a) on the footplate (9) with the opening facing forwards and the threaded hole facing up. Remove the clamping elements after use otherwise the saw blade clamping fixture (2) may be damaged when diagonal cuts are made. II) - Slide the rod on the circular-cutting and parallel guide sideways into the clamping elements (a) (centre point (c) faces downwards). III) - Slide the rod on the circular-cutting and parallel guide sideways into the clamping elements (a) (centre point (c) faces upwards). Clean the saw blade clamping fixture regularly and thoroughly by blowing with compressed air. [. . . ] Only for EU countries: Never dispose of power tools in your household waste!In accordance with European Guideline 2002/96/EC on used electronic and electric equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling. M = Torque T1 = Maximum material thickness in wood T2 = Maximum material thickness in nonferrous metals T3 = Maximum material thickness in sheet steel n0 = Stroke rate at idle speed P1 = Nominal power input P2 = Power output m = Weight without mains cable Measured values determined in conformity with EN 60745. Machine in protection class II ~ Alternating current The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards). [. . . ]