User manual MICROMEGA IA-100

[. . . ] HEADPHONE: To switch on the Headphone output and switch off the speakers. A blue LED located below the central knob indicates the unit is in standby. DISPLAY - Check that the mains voltage indicated on both the carton and the rear of the unit correspond to the local power supply - If you are in any doubt, consult your dealer. INSTALLATION In order to obtain the maximum performance of A60, it is important to follow the installation instructions. Wherever possible, we recommend that your amplifier is installed in an audio rack or other suitable furniture that provides sufficient ventilation. [. . . ] When in Stereo mode your amplifier will control the level of your active subwoofer while when in PRO-ON mode the audio-video processor will take control over your active subwoofer. This unique feature allows a complete different subwoofer set-up between stereo mode and home cinema mode. ANALOG INPUTS NAMES The four analog inputs AN1, AN2, AN3, et AN4 can be renamed using the internal name library of the microcontroller of your amplifier. The following names are available: OFF, CD, FM, DVD, TV, SAT, VCR, AUX, AV1, AV2, MP3, SPE, PVR and GAME. To replace the name of a source, place your amplifier on this source and make a long pressure on the second key INPUT SELECT >. The display shows then: The headphone socket is located on the front panel of the unit. The headphone volume setting is independent of the loudspeaker volume. The display will indicate: Note: When headphones are in use, the loudspeaker output is automatically disconnected. The headphone logo disappears and the unit returns to its previous setup including volume level. MONITOR This function allows full record monitoring when combined with a three head recording device. It also allows insertion of another unti in the listening loop ( equalizer. . . ) - Press the MON/PRO key. - The amplifier is now in monitor mode and the source is TAPE - Press once again the MON/PRO key to return to normal operation. PRO ON (MONITOR) The PRO ON mode allows to use the power amplifier section of your amplifier in combination with an external multi-channel Audio processor like AP-180. A long pressure (2 seconds) on the MON/PRO key and the display will indicate: Using the central rotary knob the name between the brackets will scroll through the list of available names until you find the one you are looking for. If you wish to change another input name press again on the INPUT SELECT > key and proceed in the same way. Once your choice is done wait 5 seconds and your amplifier will revert to normal operation. During the change of name, listening continues normally without any interruption. REMOVING AN INPUT [OFF] While you are setting the names on the four analog inputs, the name [OFF] appears in the list of available names. If you choose to name one or more inputs with this name, the selected inputs will be removed from the listening loop. Example: You have three sources, a vinyl turntable connected to PHONO input, a CD player that you have connected to AN2 named CD and a FM tuner connected to AN4 named FM. If you scroll through the inputs, your amplifier will indicate: PHO, AN1, CD, AN3, FM, iPod. If you wish that AN1 and AN3 do not appear when selecting the different inputs, you should assign them with the name [OFF]. SPECIAL NAMES (CD, FM) In the list of available names, two names CD and FM are different than the other ones. If an analog input has been named CD, a short pressure on the CD key of the Micromega system remote control handset will set your Micromega CD player out of standby if it was, set also your amplifier out of standby if it was and set your amplifier automatically on the CD input. [. . . ] 2 x 100 W Power (IA-180 / 4Ω) ………………………………………………………………………………………………………………………………. . . . …. 2 x 180 W Output Impedance ………………………………………………………………………………………………………………………. …. . ……. 0. 02 Ω / 1 kHz Power Bandwidth (30 W / 4Ω / -3dB)…………………………………………………………………………………………………. ………. . 10 Hz - 100kHz Input Sensitivity /Impedance : AN1, AN2, AN3, AN4, iPod. …………………………………………………………………………………………………. ………. . . …… 280 mV / 47 kΩ PHONO ……………………………. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]