User manual MINOURA VERGO EXCEL

[. . . ] · Adjust the roller pressure to the rear tire properly in order to maximize your tire life. Tire and roller contact will eventually wear both your tire and the trainer roller. · Check and adjust the remote shifter cable tension when you cannot set at L or H even though you turn the shifter lever. · Touching the spinning wheel and/or any other moving parts while training may cause serious injury. [. . . ] · It is not possible to convert the remote controllable resistance unit to the non-remote version one due to a difference in the inside mechanism. · If you feel any strange noise or smell, stop using V150 immediately and contact the retailer where you purchased the V150. · Any warranty will be void if you use V150 for other purpose than instructed. Minorua offers 1-year limited warranty on the resistance unit and 5-year limited warranty on the frame from the date of your purchase for any problem caused by manufacturer's defect. Any damage or problem caused by transporting process is not covered under warranty. Any damage from shipping or moving must be made to the shipping company. Read enclosed "Minoura Limited Warranty Policy" card for more detail. - Page 2 - VERGO EXCEL Schematics UF-9 UF-6 UF-7 UF-8 UF-17 GM-20 M8-4 UF-13 UF-13 GM-9 GM-7 GM-10 GM-11 GM-12 GM-13 GM-6 GM-5 GM-4 { GM-15 GM-3 GM-2 GM-16 GM-14 UF-6: RightSideCoupling&ClampLever UF-7: ClampLeverGuide UF-8: LeftSideCoupling UF-9: CouplingLockRing(Red) UF-13:RubberCap(45mm) M8-4: RubberFootCap(35mm) GM-2: AlloyRotor GM-3: HousingCover GM-5: MainHousing GM-6: DriveRoller, Axle&Bearing GM-7: DriveRollerHolder GM-9: AxleEndCap GM-10:MagUnitFittingBracket GM-11:RubberShim GM-12:MountBase GM-13:RubberWasher&BoltSet GM-14:FootPedal GM-15:MicroAdjustKnob GM-16:Flywheel(1. 5kgsforV130/150) GM-20:RemoteShifter(ChromePlated) UF-17:VERGO EXCELMainFrame(White) GM-4: NeodymiumMagnet(forV130/150/270) - Page 3 - How To Setup Your V150 Trainer Required Tools: 1x10mmSpanner 1xM4HexWrench 1. Replace your rear wheel quick release skewer to the supplied one. ! Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub Nut Axle". Minoura doesn't guarantee the stability if you don't replace the left side coupling. J) 2) Turn the Micro Adjust Knob clockwise until the roller comes close to the rear tire 2 - 3 mm. Keep them separated. (Fig. J) TIPS:If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob. J) ! The best position is that the roller compresses the tire in the depth of 3 - 4 mm. Please note too much and too less roller pressure will bring premature tire wear. Keep correct roller pressure and maintain the air pressure in correct level before using V150. (Fig. K) TIPS Foot Pedal can repeat the same compression by just pushing down the pedal. 6. The rear tire should sit in the almost center part of the Drive Roller without touching any other parts. If the tire has touched the plastic parts due to some reasons like the rear wheel is not trued correctly or you have installed a too fat tire, you must adjust the Mag unit position. To do so, loosen the backside screws with M5 hex wrench, adjust the roller position, then tighten the screws again tightly. ! If the rear tire has touched any other parts than the Drive Roller, the part may be damaged and your tire will wear out quickly. It is impossible to adjust the rear wheel position by adjusting the left side coupling position. It just works to adjust the coupling distance. 5. To remove the bike from V150, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller. How To Adjust Resistance Level V150 features a convenient remote shifter lever. [. . . ] It is impossible to adjust the rear wheel position by adjusting the left side coupling position. It just works to adjust the coupling distance. 5. To remove the bike from V150, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller. How To Adjust Resistance Level V150 features a convenient remote shifter lever. You can install it on the handlebar or stem, then you can control the resistance level without getting off the bike. 1. Wind the band around the handlebar and hook the metal ring to the gutter on the remote shifter base. (see Fig. N-2). following section. If it is loosened, adjust the band tighter as per instructed in the 3. The soft fabric band is pre-adjusted to fit normal 22mm diameter handlebar. If you need to mount onto an oversized or specially shaped handlebar or stem, adjust the band (see Fig. [. . . ]