User manual MIRAGE SPEAKERS PS8

[. . . ] If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, please refer to the operating instructions. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. [. . . ] Mirage's proprietary Clipping Protection Circuit (CPC) continuously senses the input signal level and automatically adjusts to prevent clipping of the wave form, maintaining undistorted bass reproduction. High Level Inputs The High Level inputs allow you to connect your subwoofer to the speaker outputs of any A/V Receiver or power amplifier. Low-Level RCA Input Jacks The two RCA Input jacks allow you to connect your subwoofer to EITHER: 1) The subwoofer mono output of an A/V Receiver/Processor OR 2) The subwoofer output of an External Crossover NOTE: When using the External Crossover Input, the subwoofer Level control and LP Filter control on the subwoofer's rear panel are bypassed and have no effect on the subwoofer. In this mode, adjustments are made using the controls provided on the External Crossover. 4 owners manual PS-8/PS-10/BPS-100i OPERATING CONTROLS Subwoofer Level Control This rotary control adjusts the output level of your Mirage subwoofer and should be used to balance the level of the subwoofer with that on your main/satellite speakers. See "Set-up Calibration". LP Filter (Low-pass) Control This rotary control adjusts the high frequency roll-off of the subwoofer. Continuously variable from 50Hz to 100Hz, it is used to precisely match the subwoofer bass reproduction with that of your main/satellite speakers. See "Set-up Calibration". ROOM ACOUSTICS AND SUBWOOFER PLACEMENT Mirage subwoofers can be placed virtually anywhere in your listening room without significantly affecting the stereo image of your main speakers. However, interactions between any subwoofer and room acoustic properties will have some impact on the overall bass performance. Reading this section will help you to find a placement for the subwoofer in your room which will yield the best bass performance. CAUTION: MIRAGE SUBWOOFERS HAVE A BUILT-IN AMPLIFIER AND MUST HAVE ADEQUATE VENTILATION FOR COOLING PURPOSES. DO NOT PLACE THE SUBWOOFER NEAR HEAT SOURCES, OR ANYTHING WHICH MIGHT OBSTRUCT VENTILATION. Although a clear path between the subwoofer and listening position is not required, it is important to leave approximately 4 inches of clearance between the subwoofer and walls or room furnishings. Generally, shorter runs of hook-up cables are preferable (and easier to hide), therefore locating your subwoofer relatively close to your audio equipment is often desirable. The interaction between room acoustics and any subwoofer is closely related to the subwoofer's proximity to the walls. Typically, subwoofer placement directly in or close to a corner will produce the most bass output, placement along one wall but away from a corner will produce less bass output, and placement of the subwoofer further into the room will produce the least amount of bass output. It should also be realized that the corner location, although producing the most bass output often yields ill-defined or "boomy" bass. The latter two locations will deliver progressively more accurate bass performance. 5 PS-8/PS-10/BPS-100i owners manual SUBWOOFER SUBWOOFER SUBWOOFER MOST BASS OUTPUT, BUT MAY BE "BOOMY". MODERATE BASS OUTPUT WITH SMOOTHER PERFORMANCE. LESS BASS OUTPUT, BUT WITH BEST PERFORMANCE. We urge you to experiment with various subwoofer placements in your listening room to find the position which produces "deep and smooth" performance. Often, moving the subwoofer a foot or two can make a big sonic improvement. [. . . ] The warranty does not cover damage caused during shipment, by accident, misuse, abuse, neglect, unauthorized product modification, failure to follow the instructions outlined in the owner's manual, failure to perform routine maintenance, damage resulting from unauthorized repairs or claims based upon misrepresentations of the warranty by the seller. Warranty Service: If you require service for your Mirage loudspeaker(s) at any time during the one (1) year warranty period, please contact: 1) the dealer from whom you purchased the product(s), 2) Mirage National Service, 203 Eggert Road, Buffalo, N. Y. 14215 Tel: 716-896-9801or 3) Mirage Loudspeakers, a division of Audio Products International Corp. , 3641 McNicoll Avenue, Scarborough, Ontario, Canada, M1X 1G5, Tel: 416-321-1800. You will be responsible for transporting the speakers in adequate packaging to protect them from damage in transit and for the shipping costs to an authorized Mirage service center or to Mirage Loudspeakers. If the product is returned for repair to Mirage Loudspeakers in Scarborough or Buffalo, the costs of the return shipment to you will be paid by Mirage, provided the repairs concerned fall within the Limited Warranty. [. . . ]