User manual MISSION POWERED SUBWOOFERS

[. . . ] Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures are necessary to correct the interference. CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class B . The specification is subject to change without notice. ii Table of Contents CHAPTER 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FUNCTIONS AND FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PACKING LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the WAN port is assigned a dynamic IP, there may appear a "Renew" or "Release" button on the Sidenote column. Renew IP Forever: this feature enable this product renew IP address automatically when the lease time is being expired even the system is in idle state. 16 Virtual Computers Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-to-one mapping of multiple global IP address and local IP address. Local IP: Enter the local IP address of your LAN PC corresponding to the global IP address. Enable: Check this item to enable the Virtual Computer feature. This feature is only available in WAN type of Static IP Address, Dynamic IP Address and Dynamic IP Address with Road Runner Session. 4. 4. 1. 4 PPP over Ethernet 1. PPPoE Account and Password: the account and password your ISP assigned to you. Maximum Idle Time: the amount of time of inactivity before disconnecting your PPPoE session. 17 4. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned to you. PPTP Account and Password: the account and password your ISP assigned to you. Maximum Idle Time: the time of no activity to disconnect your PPTP session. If Auto-reconnect is enabled, this product will automatically connect to ISP after system is restarted or connection is dropped. 4. 4. 1. 6 L2TP 1. It allows a computer to be exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet telephony and other special applications. Non-standard FTP port You have to configure this item if you want to access an FTP server whose port number is not 21. This setting will be lost after rebooting. 25 4. 6 Security Settings 26 4. 6. 1 Packet Filter Packet Filter enables you to control what packets are allowed to pass the router. However, Inbound filter applies on packets that destined to Virtual Servers or DMZ host only. Deny all to pass except those match the specified rules You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the following: Source IP address Source port address Destination IP address Destination port address Protocol: TCP or UDP or both. Use Rule# For source or destination IP address, you can define a single IP address (4. 3. 2. 1) or a range of IP addresses (4. 3. 2. 1-4. 3. 2. 254). For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add prefix 27 "T" or "U" to specify TCP or UDP protocol. Packet Filter can work with Scheduling Rules, and give user more flexibility on Access control. Each rule can be enabled or disabled individually. Inbound Filter: To enable Inbound Packet Filter click, please check the box next to Enable in the Inbound Packet Filter field. [. . . ] You have to define: Provider Host Name 43 Username/E-mail Password/Key You will get this information when you register an account on a Dynamic DNS server. Example: After Dynamic DNS setting is configured, click the save button. 44 4. 7. 4 SNMP Setting In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the capability to remotely manage a computer network by polling and setting terminal values and monitoring network events. Enable SNMP You must check either Local or Remote or both to enable SNMP function. Get Community Setting the community of GetRequest your device will response. [. . . ]