User manual MITSUBISHI PEFY-P15

[. . . ] DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. When using the projector in the U. S. A. , use the specified power cord (246C483-10). For details, please contact your dealer. When using the projector in Europe: COMPLIANCE NOTICE This projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Directive". [. . . ] Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10. ) · When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. Repeat steps 4 to 7, if necessary. EN-21 Viewing computer images (continued) OFF ( ) button POWER button POWER STATUS AUTO POSITION button BLANK button To stop projecting: 8. Press the POWER button on the projector or the OFF ( ) button on the remote control. · To cancel the procedure, leave the projector for a while or press the MENU button. Press the POWER button on the projector or the OFF ( ) button on the remote control again. · The lamp goes out and the projector goes into a standby mode. · During this period of one minute in the standby mode, the intake fan and exhaust fan rotate to cool the lamp. · The lamp can't be lit again for one minute after turning off the projector for safety purpose. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button. · The air outlet fans rotate faster as the temperature around the projector rises. Press the just. or button to select an item to ad- AUTO POWER ON AUTO POWER OFF OFF OFF 5. Set the selected item by pressing the ton. AUTO POWER ON AUTO POWER OFF OFF 30 min or but- SVGA60 AV MEMORY 1 IMAGE 2. Press the opt. or button to select a menu to use. SVGA60 AV MEMORY 1 To cancel the menu: 6. Important: · When the MENU button doesn't function, unplug the power cord from the wall outlet. · After selecting the items marked with , press the ENTER button. INSTALLATION 3. Press the ENTER button (or opt. button). SVGA60 AV MEMORY 1 STANDARD 1000H INSTALLATION LAMP MODE LAMP TIME (LOW) Available settings in the menus Set the following items on their relevant menus. 1. INSTALLATION menu SVGA60 AV MEMORY 1 AUTO 0 0 MEDIUM 0 0 0 0 0 ON 3. FEATURE menu SVGA60 AV MEMORY 1 STANDARD 1000H OFF OFF ON BLUE OFF OFF AË opt. opt. SVGA60 AV MEMORY 1 AUTO DISPLAY INPUT 1. AUTO AUTO AUTO OFF English OK IMAGE GAMMA MODE CONTRAST BRIGHTNESS COLOR TEMP. COLOR TINT SHARPNESS BrilliantColorTM VERTICAL LOCATION INSTALLATION LAMP MODE LAMP TIME (LOW) AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TRIGGER OUT TEST PATTERN FEATURE ASPECT PASSWORD FUNCTION MENU POSITION CINEMA MODE ? VIDEO SIGNAL SET UP SCART INPUT LANGUAGE RESET ALL CROSS HATCH 1. IMAGE menu ITEM GAMMA MODE SETTING AUTO SPORTS VIDEO CINEMA USER1 / USER2 ±30 CONTRAST ±30 BRIGHTNESS 5 options COLOR TEMP. [. . . ] · If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. · In the case of XGA, the right side of the image may not appear. In this case, adjust TRACKING in the SIGNAL menu. · TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO IN or S-VIDEO IN terminal, the signal mode is indicated as TV60 or TV50. [. . . ]