User manual MITSUBISHI PMFY

[. . . ] Use the attached RGB cable and RS-3C cable and the shielded LAN cable with this equipment so as to keep interference within the limit of a FCC Class B device. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. When using the projector in Europe: COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 9/31/EEC and 93/68/EEC, and 006/95/ EC "Low Voltage Directive". [. . . ] (See page 8. ) · When the COMPUTER1, COMPUTER or DVI is selected as the input source, COLOR can't be adjusted. (See page 8. ) · When the COMPUTER1, COMPUTER or DVI is selected as the input source, TINT can't be adjusted. (See page 8. ) Use to reduce noise and roughness in the image when noisy video signal is input. The input level of video signal differs among devices to be connected. High input level causes solid white in displayed image and low input level causes displayed image to get dark. Use this menu to adjust the input level of analog video signal. EN-3 Menu operation (continued) 2. INSTALLATION menu opt. INSTALLATION WALL SCREEN LAMP MODE AUTO POWER ON AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN BACK COLOR MUTE MODE IMAGE REVERSE BEIGE STANDARD OFF OFF SETUP ON BLUE BLACK OFF ON ITEM WALL SCREEN LAMP MODE SETTING OFF / BEIGE / LIGHT BLUE / LIGHT GREEN / PINK / BLACK BOARD STANDARD LOW FUNCTION Select any option depending on the color of the wall on which images are projected. When selecting any option other than BLACK BOARD, you can make fine adjustment of color tone (1 to 5). (See page 11. ) Select this option when you want to view images in a well-lit room. · When the lamp mode is switched, the projected image may flicker. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. When SCART INPUT is set to ON, nothing is output to the external monitor. When SCART INPUT is set to ON, normal computer signals aren't projected. Use a SCART-BNC (or SCART-Mini D-SUB 15-pin) cable (option) when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-5 Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - RESOLUTION (MEMORIZE) menu opt. SIGNAL - USER menu opt. SIGNAL A U H V SIGNAL AUTO 1024x768 0 0 0 0 RGB 100% OFF OK SIGNAL USER 75. 04 Hz 60. 02 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 RGB RGB COMPUTER INPUT OVER SCAN HOLD USER 4. SIGNAL menu ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY / FUNCTION Use to select the setting of RESOLUTION (MEMORIZE) already saved. It optimizes the signal format automatically depending on the type of video signal supplied from the computer. To change the current setting, press the ENTER button to display the RESOLUTION (MEMORIZE) menu. The vertical frequency of the currently projected video signal is displayed. [. . . ] This projector doesn't support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). *: Composite Sync EN-45 REAL mode When moire patterns or lines of uneven thickness appear on the projected image, these symptoms may be improved by displaying it in its original image size (REAL mode). To display the image in the REAL mode, set ASPECT of the FEATURE menu to REAL. (See page 3 for menu setting. ) · In the REAL mode, you cannot change the magnification factor and magnification range. [. . . ]