User manual MITSUBISHI XL7000U

[. . . ] LCD PROJECTOR MODEL XL7000U User Manual This User Manual is important to you. Please read it before using your projector. XL7000 U CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] LENS SHIFT RESET OK Use to reset the position of the lens to the factory setting. MANUAL Use to adjust the amount of transmission signal correction when a long DVI cable is used. • Regardless of the setting of LAMP MODE, the LOW lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to STANDARD, the lamp mode changes from LOW to STANDARD about 2 minutes after turn-on. • When the ambient operating temperature is high, the brightness of the lamp isn’t changed by switching the lamp mode. • When the lamp mode is switched, the projected image may flicker. • An icon is displayed to the right of the menu bar while the projector is warmed up. And an icon is displayed while the operating ambient temperature is high. While the icon is being displayed, the lamp may not brighten even when you change the LAMP MODE to STANDARD. • You can’t set IMAGE CAPTURE and SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to SPLASH ID SCREEN to enable the password lock. • When you set BACK COLOR to IMAGE and display the splash screen (startup screen) for a long time of period, the after-image may remain on the screen. • Don’t adjust the lens frequently with BACK COLOR set to IMAGE. • The power can be saved using the functions marked with on the icon. ITEM LAMP MODE SETTING STANDARD LOW EN-33 Menu operation (continued) FEATURE menu opt. opt. FEATURE ASPECT PROJECTOR ID PASSWORD FUNCTION MENU POSITION CINEMA MODE AË FEATURE NORMAL ALL DISPLAY INPUT 1. AUTO English STANDARD ENTER OK ADVANCED MENU VIDEO SIGNAL SETUP SCART INPUT LAMP WARNING HIDE OSD AUTO AUTO OFF STANDARD OFF LANGUAGE HIGH ALTITUDE MODE ADVANCED MENU RESET ALL ITEM ASPECT SETTING NORMAL 16:9 FULL PROJECTOR ID PASSWORD FUNCTION MENU POSITION CINEMA MODE ALL 01 to 63 DISPLAY INPUT / MENU ACCESS / SPLASH ID SCREEN 1 (upper left) / 2 (lower right) AUTO FUNCTION Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use. ) Select to expand squeezed (or horizontally compressed) images such as DVD images to 16:9. Press the ENTER button to make further settings such as positioning of the displayed image and selection of signals expanded by this function. (See page 29. ) Select to project images in full size (1024 x 768 pixels) irrespective of type of input signal. Select this option to control the projector regardless of the ID number. The film mode will be automatically activated when a film source signal is input. When flicker occurs on the screen, frame dropping or other incorrect display occurs, or jaggies on slanting lines are remarkable, select either FILM or VIDEO, which improves the symptom better. Use to select the language used in the menus. LANGUAGE FILM VIDEO / English / Español / Deutsch / Français / Italiano / / / / PORTUGUÊS / SVENSKA / POLSKI / Nederlands/ Norsk / / Türkçe / ภาษาไทย / Bahasa Indonesia / Melayu / STANDARD HIGH ALTITUDE HIGH ALTITUDE MODE Select this option for normal use. [. . . ] • When the light source lamp does not light up after carrying out the above procedure several times, replace the light source lamp. • Contact your dealer. Steady red Blinking green Off *1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted up to 3000 hours. *3: When you press the POWER button on the projector or the remote controller, the STATUS indicator blinks red three times and then resumes red illumination. [. . . ]