User manual NAPCO GEM-P400

[. . . ] Using Your GEM-P400 Security System GEMINI TUS STA ED ARM &20387(5, =(' 6(&85, 7< 6<67(0  1 2 3 4 Oi230a page 1 Tuesday, September 16, 1997 08:26 Oi230a page 2 Tuesday, September 16, 1997 08:26 Introduction Congratulations on your purchase of an advanced GEMINI-P400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of GEMINI's many convenience features and amenities. [. . . ] The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. The red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press re-enter the code, followed by. and Alarm Indication If the Red Armed light is flashing rapidly, an alarm occurred while you were away. For your own protection, leave immediately and call authorities from a neighbors phone . Silencing an Alarm In the event that the system goes into alarm due to a violated burglary zone, the siren and the keypad sounder will activate and the number of the zone in alarm will flash in the display. The keypad sounder and siren will silence, but zone in alarm will continue to flash. Press o reset this alarm memory. t 9 Oi230a page 9 Tuesday, September 16, 1997 08:26 Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by followed by . This will allow the easy pressing arming of the system by someone who is not a regular system user. Simply press trouble as described below, and then arm the system. To determine the nature of the trouble, press ollowed by count the number of keypad beeps and observe the number of the illuminated zone. If there is more than one trouble to view, will scroll to the next trouble, and then exit the TROUBLE mode if there are no more troubles to view. pressing Keypad Beeps or lashes 1 Beep F f , followed by t o view the Zone light ON 1 System Trouble Condition AC Power Failure Action This trouble will occur if AC power is not present. Make sure system transformer is plugged into AC receptacle and check the circuit breaker, otherwise call installing company for service. If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel. If the trouble does not go away in 24 hours, call installing company for service. If this is due to a temporary interruption in the telephone service, the trouble can be cleared when the service is restored by pressing ollowed by again to view the trouble, and and then o exit. If telephone service has been temporarily interrupted, the trouble will clear it is when restored. Call installing company for service. 1 Beep 2 Low Battery 1 Beep 3 Communication Failure 1 Beep 2 Beeps 4 1 Telephone Line Cut Bell/Siren Trouble f t 11 Oi230a page 11 Tuesday, September 16, 1997 08:26 Keypad Beeps or lashes 2 Beeps F System Troubles Zone light ON 3 System Trouble Condition Wireless Receiver Trouble Action A problem has been detected with the wireless receiver. Call installing company for service. 2 Beeps 3 Beeps 4 1-4 Wireless Receiver Jam A problem has been detected with a wireless receiver. Wireless Transmitter Low Battery The battery in a wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the number of the lit zone light. The replacement battery for the GEM-Trans2 door/window transmitter, GEM-PIR motion detector and GEM-GB glass break detector is the Duracell DL123A 3 volt lithium. (2 required for the GEM-PIR and GEM-GB. ) The GEM-DT Dual Technology Sensor requires 4 C cell alkaline batteries. Warning: Replace batteries only with the same type as specified above. [. . . ] IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. [. . . ]