User manual NAPCO GEM-RP3DGTL

[. . . ] OPERATING GUIDE for your GEM-RP3DGTL KEYPAD GEMINI 96 US TAT ED S RM A SYSTEM ARMED 01/01/97 12:00AM ENT A1 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME A B C 1 4 7 2 5 8 3 6 9 D 0 E F G AREA PRIOR/NO NEXT/YES COMPUTERIZED SECURITY SYSTEM R © NAPCO 1999 DESIGN PATS. PENDING 1 GEM-RP3DGTL. pub page 1 Wednesday, August 18, 1999 14:03 INTRODUCTION The GEM-RP3DGTL is a "smart", interactive, menu-driven keypad designed for your Napco control panel. This booklet contains important information about the operation of your system with this GEM-RP3DGTL Keypad. Check the Glossary for an explanation of terms that may be unfamiliar to you. [. . . ] Use this function to start exit delay manually, then exit the premises immediately. Be sure to have your alarm specialist check communications with the central station as soon as possible. If accidentally enabled, press the C button to exit. 12 13 18 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 13. If accidentally enabled, press the C button to exit. INTERIOR BYPASS FIRE/TBL SYS TBL CHIME GEM-RP3DGTL. pub page 18 Wednesday, August 18, 1999 14:03 KEYPAD FUNCTIONS 14 15 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 14. A communication failure will be indicated at the keypad by a system trouble "3" display. Repeat the test to attempt to correct a communication failure, as any successful communication will clear this display. (Not for UL-listed systems. ) Allows automatic arming to be delayed up to 4 hours, 15 minutes, as follows: INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 16 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME For a 1-hour, 15-minute delay, press [1], then the Jbutton. Fifteen minutes prior to arming, the siren will sound a 2-second warning and the keypad will begin a 15-minute countdown with the sounder pulsing. During this time, arming may be delayed an additional 1 to 4 hours (as above), or autoarming may be cancelled by arming and disarming the panel. 19 GEM-RP3DGTL. pub page 19 Wednesday, August 18, 1999 14:03 KEYPAD FUNCTIONS 17 18 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 17. Press the Jbutton to turn the displayed group on or off; press NEXT to proceed INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 19 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME to the next group, or PRIOR to scroll back to the previous group. Press the button when done. C 20 GEM-RP3DGTL. pub page 20 Wednesday, August 18, 1999 14:03 CENTRAL STATION MONITORING Your alarm specialist may have programmed your system to be monitored by a central station. The built-in digital communicator can transmit emergency signals and status reports to the central station 24 hours a day. If your system reports on arming (Closing Report), the central station will acknowledge arming. Note: If the ringback signal is not heard, call for service. Communicator Features Abort Delay. Ask your installer which of your zones have abort delay, a delay that enables you to reset the system before it communicates to the central station. · Regular Burglary (Non-24-Hour) Zone reports are aborted by disarming within the delay period. · 24-Hour Zones and zones programmed to report restores must be restored first, then the panel armed and disarmed, all within the delay period. Your system can notify the central station every time it is disarmed or 21 GEM-RP3DGTL. pub page 21 Wednesday, August 18, 1999 14:03 ADVANCED FEATURES Security Bypass/Unbypass (Security Bypass programmed?YES NO. ) In high-security applications, zones may be bypassed (or unbypassed) only if a valid code is entered first, as follows: + 1. Press the B button then the zone number (or vice versa) to deactivate that zone. Similarly, a bypassed zone may be unbypassed using the foregoing procedure. 22 GEM-RP3DGTL. pub page 22 Wednesday, August 18, 1999 14:03 ADVANCED FEATURES Start Exit Time After Ringback (for Commercial Burglary Systems only) (Start Exit Time programmed?YES NO. ) If your system reports to a central station, your panel may have been programmed to start exit delay after the central-station ringback (verification) signal. [. . . ] Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period. IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. [. . . ]