User manual NAPCO XP-400

[. . . ] $50(' 5($'< ' 6<67(0 Using Your XP-400 Security System =21( =21( =21( =21( NAPCO Oi220a page 1 Tuesday, September 16, 1997 08:30 2 Oi220a page 2 Tuesday, September 16, 1997 08:30 Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of EXPRESS' many convenience features and amenities. Your system consists of a control panel (a computer housed within a white metal panel enclosure), one or more EXPRESS Decorator Keypads for controlling the system, and various security detection devices. [. . . ] The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press the 2 Alarm Indication If the Red Armed light is flashing rapidly, an alarm occurred while you were away. For your own protection, leave immediately and call authorities from a neighbor's phone . ZONE 1 ZONE 2 ZONE 3 ZONE 4 Silencing an Alarm In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and the keypad sounder will also activate. zone which went into alarm continue flashing until 9 Oi220a page 9 Tuesday, September 16, 1997 08:30 Special Functions By pressing be enabled: Easy !f . f whi Bel f Access f f ollowed by the appropriate key, (do not press simultaneously) these special functions and features can Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by ollowed by This will allow the easy pressing arming of the system by someone who is not a regular system user. Easy Exit (when system is armed) This function (if programmed) allows an occupant to leave the premises without disarming the system. Zone lights 1 through 4 will light to indicate any User Codes presently programmed. Programming / Reprogramming User Codes 1 Press the User number to be programmed. (For example, press 2 3 ZONE 1 ZONE 2 ZONE 3 ZONE 4 o program the User 2 code. ). The keypad will beep 2 times and the corresponding Zone light will flash to indicate the user number you are about to program. Press in the 4 digits of the new User 2 code, the keypad will beep 4 times. If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the User Program Mode below. t Erasing a User Code 1 Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light 2 Press will flash to indicate the user number you are about to erase. The zone light will go out to indicate that the user code has been erased. Program Mode below. 3 If there are more user codes to be erased, return to step 1 above, otherwise, go to Exiting the user Exiting the User Program Mode When you are done programming or erasing User codes, press to Exit the User Program Mode. 11 Oi220a page 11 Tuesday, September 16, 1997 08:30 9System Troubles The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow 'SYSTEM light and beeping the keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply to view the trouble as described below, and then arm the system. press ARMED READY SYSTEM In order to determine the nature of the trouble, press , count the number of keypad beeps and observe the number of the illuminated zone light. will scroll to the next, and then exit the If there is more than one trouble to be viewed, pressing 'SYSTEM mode if there are no additional troubles to view. 'SYSTEM ZONE 1 ZONE 2 ZONE 3 ZONE 4 Keypad Beeps or Zone light ON Flashes 1 Beep 1 System Trouble Condition AC Power Failure Action This trouble will occur if AC power is not present. Make sure system transformer is plugged into AC receptacle and check circuit breaker, otherwise call installing company for service. [. . . ] IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. [. . . ]