User manual NAPCO XP-600

[. . . ] ® XP-600 & RPXP6GT keypad Control Panel/Communicator Installation Instructions © NAPCO 2005 WI1372 1/05 WI1372 XP-600 Installation Instructions Table of Contents General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (3) Backup if < 4 attemps - If Backup Reporting [45-4] has been enabled, the communicator will use Telephone Number 2 [41] for the remaining retries when there are less than 4 retries remaining. (4) Reserved Pager Programming If Pager Format ([32]and/or[42]and/or[52] = 7) is selected, pager data will be displayed as shown in Figure 8. If Pager Format is selected 4/2 format must be programmed and Sumcheck is not permitted. If a PIN number is required refer to Leading Digits [47]. [45]Communicator Features 1 (1) Communicator Enabled - Program to enable the communicator. (2) DTMF with Rotary Backup - The first attempt to communicate is dialed using the TouchTone method of dialing, subsequent attempts are dialed using the pulse method of dialing. (3) DTMF only - All attempts to communicate dial using the TouchTone method of dialing. (4) Backup Reporting to Telco 2 - After 2 attempts are made to communicate to Telco 1 the backup phone number is dialed (Telco 2). Backup Telephone Programming [40]Subscriber ID Number (Telco 2) For 4/2 format enter a 4 digit number. If 3/1 format is required enter a 3 digit number then press the i key. [41]Telephone Number 2 Program the phone number to be dialed for Telephone Number 2. A fixed dial tone detection (E) is included prior to the Dialing Prefix [44]. Dial tone detection can be disabled by programming No Dial Tone Detection [46-1]. To program any additional delay enter a "D" where required in the phone number. 000 033-1234 Leading Digits Report Code Subscriber ID Number FIGURE 8 DEFAULT PAGER DISPLAY Pager Alarm data is the same as 4/2 format with the exception that the 2 digit Report Code is transmitted before the 4 digit Subscriber ID. [46]Communicator Features 2 (1) No Dial Tone Detection - Program to disable dial tone detection for Telco 1, Telco 2 and Telco 3. (2) 2:1 Rotary Dialing - Changes the make [42]Receiver Format (Telco 2) Select the format that will be used to report 17 WI1372 XP-600 Installation Instructions NOTE: Digits in Report Codes and subscriber IDs that are programmed with "B" through "F" will be converted to "0"s. [47]Leading Digits Pager PIN Number - If a PIN number is required by the paging system, program the PIN number in the Leading Digits location. If a 7-digit PIN number is required, program the panel as follows: [31]/[41]/[51] - Pager Telephone number [32]/[42]/[52] - Select Pager Format [47] - X X X X X X X C 7-digit PIN Number Terminating Digit (#) are not transmitted. With this option selected, a telephone number programmed in Leading Digits or Trailing Digits would send the telephone number to the pager each time a report is sent. (2) Reserved (3) Reserved (4) Reserved [1] Fire [2] Panic [3] Burglary [4] Holdup [5] General Alarm [6] Reserved [7] Gas Alarm [8] Heat Alarm [9] Reserved [A] Auxiliary [B] 24 Hour [62]Zone Codes [62-1] Restore code - Zones 1 through 8. The second digit of the restore code is the zone number of the restored zone. For example, if the Zone Restore Code [62] is programmed to E, the restore code for that zone would be E4 (4/2 format). Zones that are bypassed at the time of arming send this code along with the zone number of the bypassed zone(s). For example a conditional closing by User 2, with zones 2 and 3 bypassed would be as follows: 1234 C2 F2 F3 Telephone Number 3 Programming [50] - [59] Programming is the same as for Telco 1. Refer to sections [30] through [39]. Report Codes [60]Zone Report Codes Report Code for Zones 1 through 6. 4/2 format - The Zone Report Code is the 1st digit of the report code sent, the second digit is the zone number of the reporting zone. For example, if zone 2 has a report code of 3, the report code would be 32. [. . . ] IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. [. . . ]