User manual NETOPIA 4652 SDSL-IDSL ROUTER GETTING STARTED GUIDE

[. . . ] Netopia 4652 SDSL/IDSL Router Getting Started Guide TM MAKING BROADBAND WORKTM Copyright ©2002 Netopia, Inc. , v. 053002 All rights reserved. This manual and any associated artwork, software, and product designs are copyrighted with all rights reserved. Under the copyright laws such materials may not be copied, in whole or part, without the prior written consent of Netopia, Inc. Under the law, copying includes translation to another language or format. [. . . ] These are the default communication parameters that the Netopia 4652 uses. Parameter Terminal type Suggested Value PC: ANSI-BBS Mac: ANSI, VT-100, or VT-200 Data bits 8 Parity None Stop bits 1 Speed 9600 - 57600 bits per second Flow Control None Note: The router firmware contains an autobaud detection feature. If you are at any screen on the serial console, you can change your baud rate and press Return (HyperTerminal for the PC requires a disconnect). The new baud rate is displayed at the bottom of the screen. Navigating through the Console Screens Use your keyboard to navigate the Netopia 4652's configuration screens, enter and edit information, and make choices. The following table lists the keys to use to navigate through the console screens. Move through selectable items in a screen or pop-up menu Set a change to a selected item or open a pop-up menu of options for a selected item like entering an upgrade key Change a toggle value (Yes/No, On/Off) Restore an entry or toggle value to its previous value Move one item up Move one item down Display a dump of the device event log Display a dump of the WAN event log Refresh the screen Use These Keys. . . Up, Down, Left, and Right Arrow Return or Enter Tab Esc Up arrow or Control + K Down arrow or Control + O Control + E Control + F Control + L Easy Setup 6-29 Chapter 6 Easy Setup This chapter describes how to use the Easy Setup console screens on your Netopia 4652. After completing the Easy Setup console screens, your router will be ready to connect to the Internet or another remote site. Easy Setup Console Screens Using four Easy Setup console screens, you can: Modify a connection profile for your router for the connection to your ISP or remote location Set up IP addresses and IP address serving Password­protect configuration access to your Netopia 4652 Accessing the Easy Setup console screens To access the console screens, Telnet to the Netopia Router over your Ethernet network or physically connect with a serial console cable and access the Netopia Router with a terminal emulation program. See "Connecting through a Telnet Session" on page 5-26 or "Connecting a Console Cable to Your Router" on page 5-27. Note: Before continuing, make sure you have the information that your ISP or network administrator has given you for configuring the Netopia Router. The Netopia Router's first console screen, Main Menu, appears in the terminal emulation window of the attached PC or Macintosh computer when: The Netopia Router is turned on The computer is connected to the Netopia Router Telnet or the terminal emulation software is running and configured correctly A screen similar to the following Main Menu appears: 6-30 Getting Started Guide Netopia 4652 Easy Setup. . . Quick View. . . If you do not see the Main Menu, verify that: If you are using a serial connection, that your serial port speed is the same as the Netopia 4652's default 9600 baud, for first use. The computer used to view the console screen has its serial port connected to the Netopia 4652's Console port or an Ethernet connection to one of its Ethernet ports. See "Connecting a Console Cable to Your Router" on page 5-27 or "Connecting through a Telnet Session" on page 5-26. Telnet or the terminal emulation software is configured for the recommended values. If you are connecting via the Console port, your computer's serial port is not being used by another device, such as an internal modem, or an application. Turn off all other programs (other than your terminal emulation program) that may be interfering with your access to the port. Your Netopia 4652's console access may be password protected from a previous configuration. See the Firmware User's Guide chapter on "Troubleshooting" for more suggestions. Easy Setup 6-31 Quick Easy Setup Connection Path This section may be all you need to do to configure your Netopia 4652 SDSL/IDSL Router. Below is a handy checklist: DSL Line Configuration Screen Line type SDSL-ATM (default) or (for SDSL-ATM only) Operation Mode: SDSL-HDLC or Generic Lucent Nokia EOC Fast Nokia Fixed Paradyne Nortel UE IMAS Data Rate: _______________________ IDSL (requires reboot) Data Link Encapsulation PPP (default) or PPP Mode: VC Multiplexed (default) or LLC SNAP RFC1483 Mode (SDSL-ATM Line Type only): (for Bridged 1483 only) PPP over Ethernet (PPPoE) RFC1483 or Bridged 1483 (default) or Routed 1483 PPP over Frame Relay Enabled: Off (default) or On DLCI: _______________________ LMI: (for SDSL-HDLC and ISDL Line Types only) Frame Relay or Off (default) or On ANSI (Annex D) CCITT (Annex A) LMI None (for ISDL Line Type only) HDLC Data Circuit VPI Data Circuit VPI 0-255 (0 is default) 0-65535 (38 is default) _______________________ _______________________ Easy Setup Profile Screen Address Translation Enabled: IP Addressing: Yes (default) or No Numbered (default) or Unnumbered None (default), PAP or CHAP (for Numbered IP Addressing) Local WAN IP Address: _______________________ Local WAN IP Mask: _______________________ (for PAP or CHAP) User Name (or Host Name): _______________________ (for Unnumbered IP Addressing) Remote IP Address: _______________________ Remote IP Mask: _______________________ (for PAP or CHAP) Password (or Secret): _______________________ (for PPP DLEs only) PPP Authentication: 6-32 Getting Started Guide IP Easy Setup Screen Ethernet IP Address: Ethernet Subnet Mask: Domain Name: Primary Domain Name Server: Secondary Domain Name Server: Default IP Gateway: _______________________ _______________________ _______________________ _______________________ _______________________ _______________________ Easy Setup Security Configuration Screen Write Access Name: Write Access Password: _______________________ _______________________ (192. 168. 1. 1 255. 255. 255. 0 are defaults) The following steps will get you up and running quickly: 1. If you don't know how to do this, see "Connecting through a Telnet Session" on page 5-26. Alternatively, you can connect the console cable and open a direct serial console connection, using a terminal emulator program. See "Connecting a Console Cable to Your Router" on page 5-27. Quick View. . . 2. Select the first item on the Main Menu list, Easy Setup. [. . . ] In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord. ) The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to the certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. [. . . ]