User manual NEXTEL IDEN I2000

[. . . ] NON-BT IMPORTANT R E A D THIS FIRST JABRA FreeSpeakTM QUICK START GUIDE For Nextel Phones Model #:100-91030000-02 Model #:100-91130000-02 Model #:100-91430000-02 Headset Indicator Light (Blue LED) Multi-Function Button MiniGelTM Volume Control Button BEFORE USING YOUR HEADSET Charge FreeSpeak ­ FreeSpeak is rechargeable and must be charged before use. Plug one end of the AC power adapter into the multi-adapter and the other end into an electrical wall outlet. Charge your headset for approximately 2 hours or until both blue indicator lights go out. [. . . ] If you prefer the left, gently rotate the MiniGel 180°. Make, answer, and end calls (details on p. 12-15 of User Guide) 1. To make or answer calls, press and release ONCE to move the headset from "Standby" to "Active" mode, turning on the audio link between the headset and the multi-adapter. (It may take a few seconds for the audio link to start, so don't press the again. ) In Active mode, the indicator lights flash every second. You will then need to dial or answer the call using the phone's keypad. When you're done with the call, use the phone's keypad to end the call. Then press and release again to return to Standby, turning off the audio link. Calls can be made by using voice-activated dialing (available in certain Nextel phone models). button down too long when switching modes; this should To answer and end calls with only the headset: Some phones enable you to answer or end a call by pressing and releasing without having to touch the phone. For all Nextel phone models (except the i1000), the phone's Automatic Answer feature needs to be activated for this headset feature to work. For the BlackBerry 6510, FreeSpeak's Anwer/End feature has to be turned on. To turn on FreeSpeak's Answer/End feature: 1) Ensure that the AC power adapter is not connected. 4) You will then see a number of blinks (long flashes) on the multi-adapter indicator light which tell you whether this feature is enabled or disabled according to the following table: Number of Blinks 4 5 Answer/End Feature Enabled Disabled Comments -Default Setting 5) Repeat steps 1-4 to switch between enabled and disabled settings. If you are enabling Answer/End feature for the first time, you should test answering and ending calls to ensure that your phone supports this feature. For more information, see "Enhanced Features" at www. jabra. com/fscs. Calls can be ended by the headset only by waiting for the line to disconnect. STATUS INDICATORS What you see Flashes every second What you hear When Active Mode starts: quick series of TWO tones ­ low to high pitch When Standby Mode starts: quick series of TWO tones ­ high to low pitch Status Active Mode · Call in progress · Up to 4 hours of talk time Standby Mode · Waiting for call · Up to 100 hours of standby time with mheadset in multi-adapter Flashes every 3 seconds TIPS & SOLUTIONS To prolong battery life: · After you've ended a call using your phone's keypad, always remember to place the headset in Standby mode by pressing and releasing when not in use. · Dock the headset firmly in its multi-adapter when not in use. If you press and release and the headset stays in Standby mode: button. In rare cases, this may button too long while using If FreeSpeak becomes unpaired, it will not respond to the occur when you first receive the product or when you hold the the product. [. . . ] Insert the headset into the multi-adapter for about 3 seconds, then remove. To improve audio clarity: Stay within 30 feet (10 meters) of your multi-adapter. In general, you will get the best performance when there are no obstructions (including parts of the body) between your headset and the multi-adapter. Need more help?Telephone: (858) 622-9955, Monday to Friday 8am to 5pm PST (800) EAR-2230 (USA and Canada) [. . . ]