User manual NOVAK MONGOOSE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NOVAK MONGOOSE. We hope that this NOVAK MONGOOSE user guide will be useful to you.
Manual abstract: user guide NOVAK MONGOOSE
Detailed instructions for use are in the User's Guide.
[. . . ] ESC may have shut-down &ESC'sneutralpointistoofaroff to sense that transmitter throttle has been returned to neutralRefer to Step 4. · Possible receiver damageCheck operation with a different receiver. · Possible internal damageRefer to Service Procedures.
mongoose BASIC SET-UP GUIDE
· See `Programming/Gearing' sheet for Proper Gearing, Profile Selection, Custom Programming, & LiPo Cut-Off ·
SPECIFICATIONS
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 cells (1. 2 VDC/cell), 2-3 LiPo cells ESC Footprint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 15"x0. 95" [29. 0x24. 3mm] ESC Weight (w/o wires) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 77 ounce [22 grams] B. E. C. [. . . ] 57202mmPowerConnectors--2pair--Gold plated low-loss 16-20G power connectors. 57212mmPowerConnectors--5pair--Gold plated low-loss 16-20G power connectors. 57222mmPowerConnectors--12male--Gold plated low-loss 16-20G power connectors. 57232mmPowerConnectors--12female--Gold plated low-loss 16-20G power connectors. 5825MicroBatteryCrossBars--7pcs--Gold plated oxygen-free copper micro battery bars. 5826MicroBatteryCrossBars--28pcs--Gold plated oxygen-free copper micro battery bars. 5831Lead-Free3%SilverRacingSolder--6g--Low-resistance, high-conductivity solder. 5832Lead-Free3%SilverRacingSolder--15g--Low-resistance, high-conductivity solder. 5833Lead-Free3%SilverRacingSolder--100g--Low-resistance, high-conductivity solder. 5840Double-SidedMountingTape--10pcs--1"x1" high-performance clear mounting tape. 5915Three-80SinteredRotor--Replacement sintered neodymium rotor for Three-80 motors. 5916Three-80FrontEndBell&Bearings--Replacement front end bell & both bearings.
SpeedControlRunsExcessivelyHot
· Gear ratio too lowIncrease gear ratio (see `PROPER GEAR SELECTION' section).
WATER & ELECTRONICS DON'T MIX!
ModelRunsSlowly/SlowAcceleration
NO SCHOTTKY IN BRUSHLESS-MODE!
Novak Electronics, Inc.
17032 Armstrong Avenue Irvine, CA 92614
(949) 833-8873 · FAX (949) 833-1631 Customer Service e-mail: cs@teamnovak. com Monday-Friday: 8:00am-5:00pm (PST)
· Gear ratio too highReduce gear ratio (see `PROPER GEAR SELECTION' section). · Check battery & connectorsTry another battery; replace connectors/battery if needed. · Incorrect transmitter/ESC adjustmentRefer to Step 4. · External Power Capacitor damaged/not installedReplace Power Capacitor. · Internal damageRefer to Service Procedures.
DISCONNECT BATTERIES WHEN NOT IN USE 4 TO 9 CELLS OR 2-3 CELL LiPo ONLY
ESCIsMeltedOrBurnt/ESCRunsWithSwitchOff
Always disconnect the battery pack from the speed control when not in use to avoid short circuits and possible fire hazard.
*For more assistance call our Customer Service Department or check our website.
service procedures
Before sending your speed control or brushless motor system in for service, review Trouble-Shooting guide and instructions. After reviewing instructions, if you feel that your ESC/system requires service, please obtain the most current product service options and pricing by the following ways:
WEBSITE: Print a copy of the PRODUCT SERVICE FORM from the CUSTOMER SERVICE
section of the website. Fill out the needed information on this form and return it with the Novak product that requires servicing.
If using Ni-Cd or Ni-MH batteries, NEVER use fewer than 4 or more than 9 cells (1. 2VDC/cell) in the vehicle's main battery pack. If using LiPo batteries, ONLY use a 2-cell (2S) or 3-cell (3S) pack for the vehicle's main battery & be sure the correct LiPo Cut-Off programming option is turned ON. The Mongoose is designed for use with sensor-based Novak Brushless Motors. Failure to use Capacitor may result in higher temperatures & possible thermal shut-down or damage. Always turn on the power of the transmitter first so that you will have control of the vehicle when you turn it on. [. . . ] There is a small plastic tab that grabs a small raised barb on the back of the metal socket crimped onto the Teflon wire's end. The plastic tab should be checked to make sure it has not deformed excessively before inserting the metal socket into the plastic connector housing with the barb toward to plastic tabs. If the motor's sensor harness gets damaged, please contact our Customer Service Dept.
black orange white red blue green raised metal barb
Be sure receiver & antenna are mounted as far from ESC, power wires, battery, & servo as possible--these components all emit RF noise when throttle is applied. On graphite or aluminum chassis vehicles, it may help to place receiver on edge with crystal & antenna as far above chassis as possible.
Note: Mount antenna as close to receiver as possible--trail any excess wire off top of antenna mast (cutting or coiling excess antenna wire will reduce radio range).
Orange motor phase wire not used in Brush-Mode
1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVAK MONGOOSE
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVAK MONGOOSE will begin.