User manual NOVATION SUPERNOVA II

[. . . ] 1 - Keypad Section 4 This section contains all the buttons used to select sounds. 1-E 0 ffects Section 2 BACK PANEL SPDIF out in out in pedal/switch 3 thru midi out in 8 aux 3 7 6 aux 2 5 4 aux 1 3 2 master 1 input/sw2 input/sw1 (sustain) phones OI 1 2 3 4 5 6 7 8 9 This section contains all the knobs and buttons associated with the Effects section. This switch turns the mains power supply in the Supernova II keyboard on and off. Edited and newly-created Programs or Performances that have not been written into a memory location will be lost when the Supernova II keyboard is switched off. [. . . ] No audible effect to these sound sources will be heard if an attempt is made to adjust this parameter when these sound sources are selected and the display will show "Not Available". Sync Mod Depth Wheel Button Knob Button This combination controls the modulation of the Sync Effect on the selected Oscillator by the Mod Wheel. Turning the Mod Depth Knob fully clockwise introduces Sync Effect from the Mod Wheel to the selected Oscillator in a Positive direction. Turning the Mod Depth Knob fully anticlockwise introduces Sync Effect from the Mod Wheel to the selected Oscillator in a Negative direction. The range of this parameter is -64 to +63. 86 OSCILLATOR SECTION NOTE: This does not apply to the Noise, 1*3 & 2*3 Ring Modulator outputs. No audible effect to these sound sources will be heard if an attempt is made to adjust this parameter when these sound sources are selected and the display will show "Not Available". Harden LevelButton Knob This combination controls the Harden Effect on the selected Oscillator or noise waveforms. Turning the Level Knob fully clockwise introduces the Harden effect fully to the selected Oscillator and fully anticlockwise, there is no Hardening at all. The range of this parameter is 000 to 127. NOTE: This does not apply to the 1*3 & 2*3 Ring Modulator outputs. No audible effect to these sound sources will be heard if an attempt is made to adjust this parameter when these sound sources are selected and the display will show "Not Available". Harden Mod Depth LFO 1 Button Knob Button This combination controls the modulation of the Harden effect of the selected Oscillator by LFO 1. Turning the Mod Depth Knob fully clockwise introduces Harden from LFO 1 to the selected Oscillator in a Positive direction. Turning the Mod Depth Knob fully anticlockwise introduces Harden from LFO 1 to the selected Oscillator in a Negative direction. The range of this parameter is -64 to +63. NOTE: This does not apply to the Oscillators that have the, 1*3 & 2*3 Ring Modulator outputs. No audible effect to these sound sources will be heard if an attempt is made to adjust this parameter when these sound sources are selected and the display will show "Not Available". Harden Mod Depth LFO 2 Button Knob Button This combination controls the modulation of the Harden Effect on the selected Oscillator by LFO 2. Turning the Mod Depth Knob fully clockwise introduces Harden Effect from LFO 2 to the selected Oscillator in a Positive direction. Turning the Mod Depth Knob fully anticlockwise introduces Harden Effect from LFO 2 to the selected Oscillator in a Negative direction. The range of this parameter is -64 to +63. NOTE: This does not apply to the 1*3 & 2*3 Ring Modulator outputs. No audible effect to these sound sources will be heard if an attempt is made to adjust this parameter when these sound sources are selected and the display will show "Not Available". Harden Mod Depth ENV 2 Button Knob Button This combination controls the modulation of the Harden Effect on the selected Oscillator by ENV 2. Turning the Mod Depth Knob fully clockwise introduces Harden Effect from ENV 2 to the selected Oscillator in a Positive direction. [. . . ] This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilise power outlets that are on different branch (Circuit breaker or fuse) circuits or install AC line filter/s. [. . . ]